Document Outline

• Introduction
  • UDS-10
  • UDS-10B
  • UDS-10-IAP Device Server
    • Industrial Automation Protocols
  • Network Protocols
    • Packing Algorithm
    • IP Address
    • Port Number
  • Serial Interface
  • RJ-45 Ethernet Interface
  • Ethernet Cable
  • Serial Interface Connection
  • LEDs
  • Dimensions
  • Product Information Label
  • Software Support
  • Power Requirements
  • Reset Switch
  • Technical Specifications
• Getting Started
  • Addresses and Port Number
    • Ethernet (MAC) Address
    • Internet Protocol (IP) Address
    • Port Number
  • Physically Connecting the Unit
  • Methods of Assigning the IP Address
    • DHCP
    • AutoIP
  • DeviceInstaller
    • Install DeviceInstaller Software
    • Assign IP Address and Network Class
    • Test the IP Address
    • Add the Unit to the Manage List
    • Opening a Configuration Window
  • ARP and Telnet
  • Serial Port Login
• Configuring the Unit
  • Configuring via Web Browser
  • Using DeviceInstaller
  • Web Manager Page
    • Unit Configuration
    • Server Properties
    • Port Properties
    • Technical Support
    • Update Settings
  • Configuring via the Setup Mode Window
    • Using a Telnet Connection
    • Using the Serial Port
  • Server Configuration (Network Configuration)
    • IP Address
    • Set Gateway IP Address
    • Netmask: Number of Bits for Host Part
    • Change Telnet configuration password
    • DHCP Naming
  • Channel 1 Configuration (Serial Port Parameters)
    • Baudrate
    • I/F (Interface) Mode
    • Flow
    • Port Number
    • Connect Mode
    • Remote IP Address
    • Remote Port
    • DisConnMode
    • Flush Mode (Buffer Flushing)
    • Pack Control
    • DisConnTime (Inactivity Timeout)
    • Send Characters
    • Telnet Terminal Type
    • Channel (Port) Password
  • Expert Settings
    • TCP Keepalive time in s
  • Security Settings
    • Disable SNMP
    • SNMP Community Name
    • Disable Telnet Setup
    • Disable TFTP Firmware Upgrade
    • Disable Port 77FE (Hex)
    • Disable Web Server
    • Enable Enhanced Password
  • Factory Defaults
  • Exit Configuration Mode
  • Get Configuration
  • Set Configuration
• Updating Protocol (Firmware)
  • Protocol Firmware
  • Reloading Protocol Firmware
    • Via DeviceInstaller
    • Via TFTP
    • Via Another Unit
    • Via the Serial Port
• DeviceComm Manager
  • Installing DeviceComm Manager
    • Install DeviceComm Manager
    • Setup
• Troubleshooting
  • Technical Support
    • Technical Support
• Monitor Mode
  • Monitor Mode
    • Entering Monitor Mode Via the Serial Port
    • Entering Monitor Mode Via the Network Port
    • Monitor Mode Commands
• Network Configuration using UDP
  • UDP Datagrams
  • Configuring Multiple Devices
    • Acquiring a Valid Setup Record
    • Sending a Setup Record
    • The Intel Hex Format
    • Calculating the Checksum
    • Calculating the Two’s Complement
  • Setup Records
    • Channel Parameters
    • Interface Mode
    • Baud Rate
    • Flow Control
    • Connect Mode
    • Disconnect Mode
    • Flush Mode (Buffer Flushing)
    • Pack Control
  • IP Addresses
    • Network Portion
    • Subnet Portion
    • Host Portion
    • Network Address
    • Broadcast Address
    • Private IP Networks and the Internet
    • Network RFCs
• Binary to Hex Conversion
  • Connect Mode Options
  • Disconnect Mode Options
  • Flush Mode (Buffer Flushing) Options
  • Interface Mode Options
  • Pack Control Options
• IP Addresses
  • Class A Network
  • Class B Network
  • Class C Network
  • Network Address
  • Broadcast Address
  • IP Netmask
  • Private IP Networks and the Internet
  • Network RFCs
• Glossary of Terms