Quantum 10K II - Manual (Page 366)

Quantum Atlas 10K II Ultra 160/m SCSI Hard Disk Drives I − 1
INDEX
—A—
ABORT TASK Message, B-28
ABORT TASK SET Message, B-28
Acoustic Emissions, 4-10
Activity LED, 3-14
Additional Sense Codes, 5-179
Additional Sense Length, 5-173, 5-174
AIP, starting, 5-98
ANSI Version, 5-35, 5-36
ARBITRATION Phase, B-13
ASCII Implemented Operating Definition Page,
5-37
Asynchronous Data Transfer, B-18
Attention Condition, B-23
—B—
Bit Pointer, 5-187
Block Format Defect Descriptor, 5-26
Block Length in Bytes, 5-141, 5-142
Buffer Empty Ratio, 5-68, 5-69
Buffer Full Ratio, 5-68, 5-69
Buffer ID, 5-139, 5-140, 5-221
Buffer Offset, 5-139, 5-140, 5-221
Build Date and Time, 5-43
Bus Inactivity Limit, 5-68, 5-69, 5-70
Bus Phases, B-12
—C—
Cables, 3-28
Cache Table Size, 5-110
Caching Page, 5-74
CHANGE DEFINITION Command, 5-23
Changeable Pages, 5-60, 5-61, 5-63
CLEAR ACA Message, B-29
CLEAR QUEUE, 5-9
CLEAR TASK SET Message, B-29
Clearing Sense Data, 5-172
COMMAND COMPLETE Message, 5-13
Configuration Jumpers and Connections, 3-6
Configuring SCSI ID (Ultra 160/m SCSI
Versions with 68-Pin Connector), 3-8
Configuring SCSI ID for SCA-2 Connector
Versions, 3-12
Connect Time Limit, 5-68, 5-69
CONNECTOR PINOUTS AND WIRING DIAGRAMS,
3-17
CONTINUE TASK Message, B-29
Control Mode Page, 5-76
Correction Span, 5-65, 5-67, 5-74
Cylinder Number of Defect, 5-30, 5-146
Cylinder Skew Factor, 5-107, 5-108
—D—
Data Strobe Offset Count, 5-65
Data Verification, 6-5
Device Identification Page, 5-37, 5-41
Device Type Modifier, 5-35
DISCONNECT message, B-30
Disconnect Time Limit, 5-68, 5-69
Disconnect-Reconnect Mode Page, 5-60, 5-68
Disk Controller Hardware Revision Number,
5-35
Drive Connections, 3-27
Drive Installation, 3-1
Drive Serial Number, 5-35, 5-41
Drive Step Rate, 5-107, 5-108
—E—
ECMA Version, 5-35, 5-47
Electronics Pass Number, 5-35
Enable Narrow Mode (Force 8), 3-11
Ending Boundary, 5-79, 5-81
Error Reporting, 5-9
Extent List Length, 5-191, 5-192
—F—
Field Pointer Bytes, 5-188, 5-189
Firmware Revision Page, 5-37, 5-42
Force 8, 3-11
Force Single-Ended Operation, 3-15
Format Device, 5-104
Format Device Page, 5-105
FORMAT UNIT Command, 5-25
—G—
GList, 5-141, 5-143
Grown Defect List, 5-25, 5-26, 5-27, 5-28, 5-66, 5-143
—H—
HARDWARE ERROR, 5-175, 5-177
Head Number of Defect, 5-30, 5-144
HEAD OF QUEUE TAG Message, B-35
Hot Plugging, 6-11
—I—
IDENTIFY Message, B-30
IGNORE WIDE RESIDUE Message, B-31
Immed, 5-28