Quantum 10K II - Manual (Page 367)

Index
I − 2 Quantum Atlas 10K II Ultra 160/m SCSI Hard Disk Drives
Implemented Operating Definition Page, 5-36, 5-38
Information Transfer Phases, B-17
Initialization Pattern Descriptor, 5-27, 5-28, 5-30
INITIATE RECOVERY Message, B-31
INITIATOR DETECTED ERROR Message, B-31
INQUIRY Command, 5-33
Interleave, 5-26, 5-105, 5-106
ISO Version, 5-35, 5-47
—J—
Jumper Configurations and Connections – Ultra 160/m
SCSI drives with 68-Pin SCSI Connector),
3-6
Jumper Configurations and Connections for SCA-2
Connector Versions, 3-12
—L—
Landing Zone Cylinder, 5-107, 5-108
LINKED COMMAND COMPLETE (WITH FLAG) Message,
B-32
LINKED COMMAND COMPLETE Message, B-32
LOG SELECT Command, 5-51
LOG SENSE Command, 5-53
LVD DIFFSENS Driver, 6-10
LVD DIFFSENS Receiver, 6-10
LVD/SE Multimode and HVD, 6-10
—M—
Maximum Burst Size, 5-68, 5-70
Maximum Number of Notches, 5-79, 5-80
Media Error Protection, 6-4
Medium Rotation Rate, 5-107, 5-109
Medium Type, 5-62, 5-99, 5-104, 5-111
MESSAGE PARITY ERROR Message, B-33
MESSAGE REJECT Message, B-33
MLVD, 6-9
Mode Data Length, 5-62, 5-92, 5-104, 5-111
Mode Page Types, 5-61
Mode Parameter Block Descriptor, 5-58
Mode Parameter Header, 5-61, 5-62, 5-101
Mode Parameter List, 5-61
MODE SELECT (6) Command, 5-59
MODE SELECT (10) Command, 5-99
MODE SENSE (6) Command, 5-103
MODE SENSE (10) Command, 5-109
Mounting, 3-21, 3-22, 3-24
—N—
Negotiated Rate Information Page, 5-45
New Operating Definition, 5-23
NO OPERATION Message, B-34
NO SENSE, 5-92, 5-171
Non-operating Environment, 4-11
Normal commands, 5-3
NOT READY, 5-86, 5-175, 5-180, 5-181
Notch and Partition Page, 5-60, 5-79
Number of Cylinders, 5-107, 5-108
Number of Heads, 5-107, 5-108
—O—
ORDERED QUEUE TAG Message, B-35
—P—
Pages Notched, 5-81
PARALLEL PROTOCOL REQUEST Message, B-40
Parameter Code Reset, 5-51
Parameter Pointer, 5-55
Parameter Pointer Control, 5-55
Periodic Self-Adjustments, 6-7
PERSISTENT RESERVATION IN Command, 5-113
PERSISTENT RESERVATION OUT Command, 5-123
PList, 5-143, 5-145
Power Condition Page, 5-60, 5-84
Power Management, 6-6
Power Requirements, 4-7
Power-Up Self-Test, 6-7
Prefetch, 6-2
Primary Defect List, 5-25, 5-27, 5-143, 5-145, 5-147
Progress Indication, 5-171, 5-188, 5-189, 5-190
Progress Indication Bytes, 5-171, 5-189, 5-190
—Q—
Quantum Manufacturing Information Page, 5-43
Quantum-Unique Page, 5-60, 5-91
Queue Algorithm Modifier, 5-76, 5-77
Queue Tag Messages, B-34
—R—
Reallocation of Bad Blocks, 6-8
READ (6) Command, 5-135
READ (10) Command, 5-137
READ BUFFER Command, 5-139
READ CAPACITY Command, 5-141
READ DEFECT DATA Command, 5-143
READ LONG Command, 5-151
Read Retry Count, 5-65, 5-67
Read-Write Error Recovery Page, 5-65
Ready AEN Holdoff Period, 5-76
READ SKIP MASK Command, 5-153
REASSIGN BLOCKS Command, 5-155
RELEASE (6) Command, 5-163
RELEASE (10) Command, 5-165
RELEASE RECOVERY Message, B-35
Remote Busy and Fault Displays, 3-11
REPORT DEVICE IDENTIFIER Command, 5-167
REPORT LUNS Command, 5-169
REQUEST SENSE Command, 5-171
RESELECTION Phase, B-15