Document Outline

• Title
  • Copyright
• Introduction
  • Welcome to the MAX 200
  • Optional accessories
  • Optional features
  • About this guide
    • Conventions
    • Organization
  • Customer support
    • Service
    • Supplies
  • Compliance information
    • FCC Compliance in the USA
    • EME Compliance in Canada
    • Conformite EEM
  • It's illegal
    • In the USA
    • In Canada
  • Safety notes
    • Maintenance safety
    • Ozone safety
• Table of Contents
• Getting to know the MAX 200
  • Scanner
    • Front
    • Rear
  • Printer
    • Manual feed tray
  • Touch screen
    • Components
    • How do I know if a feature or option is available?
  • Scanner control panel
    • Upper components
    • Lower components
    • Information button
    • Stored jobs button
    • Meter check button
    • Custom presets button
    • Review button
    • Clear button
    • Clear all button
    • Check and repair button
    • Stop copy button
    • Interrrupt button
    • Power save button
  • Scanner document feed panel
  • Auto mode panel
  • Printer control panel
    • Messages
    • Printer diagram
    • Top indicator lamps
    • Buttons
  • Manual feed panel
  • RFC panel
  • Cut sheet panel
  • Media type and series panel
  • Media series panel (tray 5)
• MAX 200 power
  • Switching the power-on
  • Switchng the power off
  • Ground fault protectors
    • Printer ground fault
    • Scanner ground fault
  • Warm-up
  • Auto power-off mode
  • Power save
• Media
  • How to handle unusable documents
    • Torn or ripped document
    • Document with staples
    • Document with curl
    • Bent document
    • Transparent document
  • How to store cut sheet media
  • How to store roll media
  • Media type and weight charts
    • RFC drawer and manual feed tray
    • Cut sheet tray (tray 5)
  • Media size charts
    • RFC drawer
    • Tray 5
    • Manual feed tray
  • Maximum scan length
  • Maximum print length
  • How do I know when tray 5 or a drawer is empty?
    • From the auto mode panel
    • From the R/E, media, cut touch screen
    • From the RFC panel
    • From the cut sheet panel
  • How to load roll media
  • How to load cut sheet media
  • How to cut roll media
    • Auto cut
    • Manual cut
  • Heater
  • Humidifier (optional)
• How to make copies
  • Before making copies
  • In auto mode
    • Auto R/E
    • Auto 100%
    • Cut roll media
  • In manual mode
    • With the manual feed tray
• Basic touch screen features
  • Media cut mode
  • R/E; media; cut
    • Normal R/E
    • R/E by L&W
    • Normal R/E calculator
    • R/E by L&W calculator
    • Paper length adjustment
  • Image density
  • Document image type
  • Print color
    • One color (black or red)
    • Two color (black and red)
• Image quality touch screen features
  • Sharpness
  • Scan color sensitivity
• Additional touch screen features
  • Image location
  • Editing
    • Overall editing
    • Marker editing
    • Coordinates editing
• Finishing touch screen features
  • E-sorter
    • Off (uncollated)
    • Collated
    • Program
  • Stamper
    • Stamp pattern
    • Numbering
    • Stamp location
    • Date stamp
    • Stamp color
  • Folder
  • Paper exit (for machines with no folder)
• Stored jobs
  • How to store, recall or delete a job
  • Store jobs log
  • Job feature log
• How to customize the MAX 200
  • Identifying the system features
  • Identifying the copy features
  • Identifying the storage/disk manager features
  • How to enter custom presets
  • How to change the system features
    • Time & date
    • Auto power off
    • Auto power save
    • Auto clear/backlight off
    • Document width
    • Attention tone
    • Plotter setup
    • Loading stamp data
    • Additional setting
  • How to change the copy features
    • Reduce/enlarge presets
    • Media type and width for auto mode
    • Stamp location and orientation
    • Date stamp format
    • Folder setup
    • Auto/manual mode
    • Media cut mode and document orientation
    • Lead/trail edge default for synchronized
    • Variable length default
    • Background suppression level default
    • Image density
    • Document image type
    • Scan to print color default
    • Color recognition range
    • Marker area recognition
    • Additional setting
  • How to change the storage/disk manager features
    • Stamp creation/deletion
    • Disk manager (format/duplication)
    • E-sorter (program) settings
• Care
  • Cleaning the scanner platen glass
  • Ordering supplies
• Problem solving
  • Problem solving chart
  • Clearing a scanner jam
  • Clearing a printer jam
    • Indicator lamps 1 - 4
    • Indicator lamp 5
    • Indicator lamps 6 or 7
    • Indicator lamp 8
    • Indicator lamp 9
    • Indicator lamp 10
    • Indicator lamp 11 or 12
  • Replacing the toner cartridge
  • Relatch the fuser
  • Calling for service
• Scanner interface (optional)
  • Overview
• Plotter interface (optional)
  • Overview
    • How to enter copy mode from plot mode
• Technical data
  • Printer specifications
    • Physical characteristics
    • Floor space requirements
  • Scanner specifications
    • Physical characteristics
    • Floor space requirements
  • System requirements