Garmin G1000 Mooney M20TN - Manual (Page 27)

Garmin G1000 Pilot’s Guide for the Mooney M20M/M20R/M20TN 190-00647-01 Rev. B 16
SYSTEM OVERVIEW
SY
STEM
O
VER
VIEW
FLIGHT
INSTRUMENTS
EIS
AUDIO P
ANEL
& CNS
FLIGHT
MANA
GEMENT
HAZARD
AV
OID
ANCE
AFCS
ADDITIONAL FEA
TURES
APPENDICES
INDEX
BRG1 Cycles the Bearing 1 Information Window through NAV1, GPS/ waypoint identifier and GPS-
derived distance information, and ADF/frequency.
HSI FRMT Displays the softkeys for selecting the two HSI formats
360 HSI Displays HSI as a 360° compass rose
ARC HSI Displays HSI as a 140° viewable arc
BRG2 Cycles the Bearing 2 Information Window through NAV2 or GPS waypoint identifier and GPS-
derived distance information, and ADF/frequency.
ALT UNIT Displays softkeys for setting the altimeter and BARO settings to metric units
METERS When enabled, displays altimeter in meters
IN Press to display the BARO setting as inches of mercury
HPA Press to display the BARO setting as hectopacals
STD BARO Sets barometric pressure to 29.92 in Hg (1013 hPa if metric units are selected)
OBS Selects OBS mode on the CDI when navigating by GPS (only available with active leg)
CDI Cycles through GPS, VOR1, and VOR2 navigation modes on the CDI
ADF/DME Displays/removes ADF/DME Radio Tuning Window (optional; may appear as blank, ADF,
DME, or ADF/DME depending on installation)
BACK
Press the OFF or BACK Softkey to
return to the top-level softkeys.
DCLTR
DCLTR-2
DCLTR-3
DCLTR-1
TOPO ALERTS NEXRAD
(optional)
TERRAIN XM LTNG
(optional)
OFF
INSET
INSET XPDR IDENT TMR/REF NRST ALERTS OBS PFD CDI ADF/DME
(optional)
Press the CDI Softkey to cycle through
navigation sources:
- GPS
- NAV1 (VOR/LOC)
- NAV2 (VOR/LOC)
BRG2 STD BARO BACK ALERTS HSI FRMT
PFD
BRG1 ALT UNIT DME
(optional)
Press the BRG1/BRG2 softkeys to display/
remove the Bearing Information windows
and cycle through bearing sources:
- NAV1/NAV2
- GPS
- ADF
Press the STD BARO or BACK Softkey
to return to the top-level softkeys.
Press the BACK Softkey to return
to the top-level softkeys.
Press the IDENT or BACK Softkey
to return to the top-level softkeys.
XPDR
STBY ON ALT VFR IDENT BACK ALERTS CODE
IDENT BACK ALERTS 0 1 2 3 4 5 6 7 BKSP
TRFC-1
TRFC-2
STRMSCP
(optional)
DFLTS WIND
GND
Figure 1-15 PFD Configuration Softkeys
XPDR Displays transponder mode selection softkeys:
STBY Selects standby mode (Transponder does not reply to any interrogations)
ON Selects Mode A (Transponder replies to interrogations)
ALT Selects Mode C – altitude reporting mode (Transponder replies to identification and altitude
interrogations)
GND Manually selects Ground Mode, the transponder does not allow Mode A and Mode C
replies, but it does permit acquisition squitter and replies to discretely addressed Mode S
interrogations
VFR Automatically enters the VFR code (1200 in U.S.A. only)