Banks Power Ford Trucks: (Diesel ’08 - 10 6.4L Power Stroke) Tuner- Six-Gun Diesel Tuner & Banks Brake '08-10 For use with Six-Gun switch Only User Manual
Page 29
96511 v.7.0
29
Code
Event
Course of Action
1, 1
Insufficient power
supply to brake
module
Turn Ignition OFF and check connection at fuse tap, 10-pin
connection to module and 8-pin connection to Tuner. Turn
ignition back ON and re-check for presence of code. If code does
not re-appear at key ON, start engine and check for presence of
code both at engine idle and under varying driving conditions.
1, 2
Brake signal
malfunction while
brake is on
Turn Ignition OFF and check connections at 5-pin male and
female brake pedal connector. Turn ignition back ON and
re-check for presence of code. If code does not re-appear at key
ON, start engine and check for presence of code both at engine
idle and under varying driving conditions.
1, 3
Insufficient voltage
to tow-haul switch
Turn Ignition OFF and check connections at 3-pin male and
female tow-haul switch. Turn ignition back ON and re-check for
presence of code. If code does not re-appear at key ON, start
engine and check for presence of code both at engine idle and
under varying driving conditions.
1, 4
Brake Signal
malfunction while
brake is off.
Turn Ignition OFF and check connections at 5-pin male and
female brake pedal connector. Turn ignition back ON and
re-check for presence of code. If code does not re-appear at key
ON, start engine and check for presence of code both at engine
idle and under varying driving conditions.
2, 1
No response to
generated OBD ISO
messages
Turn Ignition OFF and check connections at OBD II connection.
Turn ignition back ON and re-check for presence of code. If
code does not re-appear at key ON, start engine and check for
presence of code both at engine idle and under varying driving
conditions.
2, 2
Brake pressure
switch signal
malfunction
Turn Ignition OFF and check connections at 2-pin male and
female brake pressure sensor intercept connector and 2-pin
in-cab cable connector. Turn ignition back ON and re-check for
presence of code. If code does not re-appear at key ON, start
engine and check for presence of code both at engine idle and
under varying driving conditions.
3, 1
Rear wheel slip
during braking
Module has detected rear wheel slipping. code will automatically
clear 30 seconds after traction regained.
3, 2
Power Up Error or
Internal Module
Malfunction
Turn Ignition OFF and check connection at fuse tap, 10-pin
connection to module and 8-pin connection to Tuner. Turn
ignition back ON and re-check for presence of code. If code does
not re-appear at key ON, start engine and check for presence of
code both at engine idle and under varying driving conditions.
3, 3
Internal Module
Malfunction
Turn Ignition OFF and check connection at fuse tap, 10-pin
connection to module and 8-pin connection to Tuner. Turn ignition
back ON and re-check for presence of code. If code does not
re-appear at key ON, start engine and check for presence of code
both at engine idle and under varying driving conditions.
4, 3
Exhaust Back
Pressure (EBP)
Input Voltage Out of
Range
Turn Ignition OFF and check the 96-pin male and female PcM
connectors. Turn ignition back ON and re-check for presence of
code. If code does not re-appear at key ON, start engine and check
for presence of code both at engine idle and under varying driving
conditions.
4, 4
communication
failure to brake
module.
Turn Ignition OFF and check connections at 10-pin brake module,
8-pin Tuner, and OBD II connector. Turn ignition back ON and
re-check for presence of code. If code does not re-appear at key
ON, start engine and check for presence of code both at engine idle
and under varying driving conditions.
5, 1
Internal Module
Malfunction
Turn Ignition OFF and check connections at 10-pin brake module,
8-pin Tuner, and OBD II connector. Turn ignition back ON and
re-check for presence of code. If code does not re-appear at key
ON, start engine and check for presence of code both at engine idle
and under varying driving conditions.
Table 2: Banks Brake Fault Codes