R&M Materials Handling ELECTRIC CHAIN HOISTS LoadMate Chain Hoist LM 10 Stepless - Manual (Page 46)

LM10 STEPLESS I&M MANUAL/EN/11.30.2010
46/99
This document and the information contained herein, is the exclusive property of R&M Materials Handling, Inc., and represents a non-public, confidential and proprietary trade secret that
may not be reproduced, disclosed to third parties, altered or otherwise employed in any manner whatsoever without the express written consent of R&M Materials Handling, Inc.
Copyright © (2010) R&M Materials Handling, Inc. All rights reserved.
7.5.10 Factory default parameters
Table 13. Default Factory Parameters
400V 100Hz 460V 120Hz
Label Code Default Label Code Default
G 1.1. General Parameters G 2.1. General Parameters
P 1.1.1 Password 0 P 1.1.1 Password 0
P 1.1.2 Accel Time 1.5 P 1.1.2 Accel Time 1.5
P 1.1.3 Decel Time 0.5 P 1.1.3 Decel Time 0.5
P 1.1.4 Min Freq 12 P 1.1.4 Min Freq 12
P 1.1.5 Max Freq 100 P 1.1.5 Max Freq 120
P 1.1.6 Reverse Plugging 100 P 1.1.6 Reverse Plugging 100
P 1.1.7 Stop Function Ramping P 1.1.7 Stop Function Ramping
P 1.1.8 MSFreq2/Slowdown 20 P 1.1.8 MSFreq2/Slowdown 20
P 1.1.9 Multistep Freq 3 50 P 1.1.9 Multistep Freq 3 50
P 1.1.10 Multistep Freq 4 50 P 1.1.10 Multistep Freq 4 50
P 1.1.11 Input set EP2 P 1.1.11 Input set EP2 StopLim
G 2.2. Motor Parameters G 2.2. Motor Parameters
P 1.2.1 Motor Nom Volt 400 P 1.2.1 Motor Nom Volt 460
P 1.2.2 Motor Selection Free Hoist P 1.2.2 Motor Selection Free Hoist
P 1.2.3 Number of Motors 1 P 1.2.3 Number of Motors 1
G 1.2.4 Motor Nominal Values G 1.2.4 Motor Nominal Values
P 1.2.4.1 Motor Nom Freq 100 P 1.2.4.1 Motor Nom Freq 120
P 1.2.4.2 Motor Nom Curr 4.4 P 1.2.4.2 Motor Nom Curr 4.4
P 1.2.4.3 Nom Flux Curr 2.6 P 1.2.4.3 Nom Flux Curr 2.6
P 1.2.4.4 Current Limit 7 P 1.2.4.4 Current Limit 7
P 1.2.4.5 Motor Cos Phi 0.69 P 1.2.4.5 Motor Cos Phi 0.69
P 1.2.4.6 Autotuning Not Done P 1.2.4.6 Autotuning Not Done
G 1.2.5 U/f Settings G 1.2.5 U/f Settings
P 1.2.5.1 Zero Freq Volt 4.2 P 1.2.5.1 Zero Freq Volt 4.2
P 1.2.5.2 U/f Mid Volt 4.5 P 1.2.5.2 U/f Mid Volt 4.5
P 1.2.5.3 U/f Mid Freq 3 P 1.2.5.3 U/f Mid Freq 3
P 1.2.5.4 Torque Boost On P 1.2.5.4 Torque Boost On
P 1.2.5.5 IrAdd Motor 100 P 1.2.5.5 IrAdd Motor 100
P 1.2.5.6 IrAdd Generator 0 P 1.2.5.6 IrAdd Generator 0
P 1.2.5.7 Rs Voltage Drop 99 P 1.2.5.7 Rs Voltage Drop 99
G 1.2.6 Brake Control G 1.2.6 Brake Control
P 1.2.6.1 Start Current 100 P 1.2.6.1 Start Current 100
P 1.2.6.2 Brk Opening Del 0.05 P 1.2.6.2 Brk Opening Del 0.05
P 1.2.6.3 Start DC-Time 0.1 P 1.2.6.3 Start DC-Time 0.1
P 1.2.6.4 Stop DC-Time 0.2 P 1.2.6.4 Stop DC-Time 0.2
P 1.2.6.5 Stop DC-Freq 2 P 1.2.6.5 Stop DC-Freq 2
P 1.2.6.6 Start Freq S1 4 P 1.2.6.6 Start Freq S1 4
P 1.2.6.7 Start Freq S2 3 P 1.2.6.7 Start Freq S2 3
P 1.2.6.8 Brake Stop Freq 3.5 P 1.2.6.8 Brake Stop Freq 3.5
P 1.2.6.9 Min Freq Bias S2 3 P 1.2.6.9 Min Freq Bias S2 3
G 1.3. I/O Parameters G 1.3. I/O Parameters
P 1.3.1 ROA1 Not Used P 1.3.1 ROA1 Not Used
P 1.3.2 Ain1 Min Volt 0 P 1.3.2 Ain1 Min Volt 0
P 1.3.3 Ain1 Max Volt 10 P 1.3.3 Ain1 Max Volt 10
P 1.3.4 Aout Function Motor Curr P 1.3.4 Aout Function Motor Curr
P 1.3.5 Aout Zero Curr 0 P 1.3.5 Aout Zero Curr 0
P 1.3.6 Aout Nom Curr 10 P 1.3.6 Aout Nom Curr 10
G 1.4 Protection G 1.4 Protection
P 1.4.1 Motor Thermal Prot Not Used P 1.4.1 Motor Thermal Prot Not Used
P 1.4.2 - 0 P 1.4.2 - 0
P 1.4.3 - 40 P 1.4.3 - 40
P 1.4.4 - 45 P 1.4.4 - 45
P 1.4.5 - 100 P 1.4.5 - 100
G 1.5 Expert G 1.5 Expert
P 1.5.1 Slow Down Mode Fast P 1.5.1 Slow Down Mode Fast PowerUp
P 1.5.2 S-Curve 0 P 1.5.2 S-Curve 0
P 1.5.3 Ramp Stretching 0 P 1.5.3 Ramp Stretching 0
P 1.5.4 Switching Freg 8 P 1.5.4 Switching Freg 8
P 1.5.5 Brake Chopper Run P 1.5.5 Brake Chopper Run