Maintenance and modifications, Location a, Location h – Extron Electronics Fiber Matrix 6400 User Manual

Page 122: Slot 1, O#1 i#1 slot 2, Slot 3, Slot 4

Advertising
background image

Fiber Matrix 6400 Switcher • Maintenance and Modifications

7-2

Maintenance and Modifications

Removing and Installing the I/O Board or Blank Panel

W

The Fiber Matrix 6400 fiber optic I/O boards output continuous invisible
light, which may be harmful and dangerous to the eyes; use with caution.

•

Do not look into the rear panel fiber optic cable connectors or into the

fiber optic cables themselves.

•

Plug the attached dust caps into the optical transceivers when the fiber

optic cable is unplugged.

N

As factory configured, the fiber optic I/O boards are configured as either

100 percent singlemode or 100 percent multimode, but you can remove a fiber
optic transceiver module (one input and one output) of one transmission mode
and replace it with a block of the other transmission mode.

You can mix transmission mode transceiver modules on a fiber optic I/O board,
provided that you ensure that each fiber cable and connected devices are the
appropriate transmission mode for the transceiver module.

Typically, singlemode fiber has a yellow jacket and multimode cable has an
orange jacket.

N

Unlike the FOX 500 transmitters and receivers, which output an optical

stream on one connector in a block and receive a return optical stream on the
second connector in the same block, the fiber optic I/O board uses one connector
on the block as an input and the second connector on the same block as a separate
output.

N

For proper cooling and air flow, boards and/or blank panels should be installed in

all locations during normal switcher operations.

Circuit boards can be replaced for fault correction or to accommodate SDI/HD-SDI

(electric) signals. They can be added or removed to increase or decrease the I/O

configuration (size) of the Fiber Matrix.
See figure 7-1. Each I/O board is identified by the input and output numbers supported

by the board position (1 - 8, 9 - 16, and so on) The transceiver modules on fiber optic

I/O boards and the BNC connectors on SDI/HD-SDI boards are identified as A through H.

RESET

RS232/RS422

REMO

TE

LAN

A

CT

LINK

1 - 8

9 - 16

17 - 24

25 - 32

33 - 40

OUT

IN

A

OUT

IN

B

OUT

IN

C

OUT

IN

D

OUT

IN

E

OUT

IN

F

OUT

IN

G

OUT

IN

H

OUT

IN

A

OUT

IN

B

OUT

IN

C

OUT

IN

D

OUT

IN

E

OUT

IN

F

OUT

IN

G

OUT

IN

H

OUT

IN

OUT

IN

OUT

IN

OUT

IN

OUT

IN

OUT

IN

OUT

IN

OUT

IN

MUTI-RATE SDI INPUTS

H

G

A

D

E

F

C

B

MUTI-RATE SDI OUTPUTS

H

G

A

D

E

F

C

B

Location A

Input

Location A

Output

Location H

Input

Location H

Output

Location H

Output and Input

Location A

Output and Input

Slot 1

(1-8)

O#1

I#1

Slot 2

(9-16)

Slot 3

No board

installed

Slot 4

(25-32)

O#2

I#2

O#3

I#3

O#4

I#4

O#9

I#25

I#26

I#27

I#28

I#29

I#30

I#31

I#32

O#25

O#26

O#27

O#28

O#29

O#30

O#31

O#32

I#9

O#10

I#10

O#11

I#11

O#12

I#12

O#5

I#5

O#6

I#6

O#7

I#7

O#8

I#8

O#13

I#13

O#14

I#14

O#15

I#15

O#16

I#16

A

H

H

H

A

A

Figure 7-1 — Arrangement of inputs and outputs on the I/O boards

Locations A through H correspond to the output and input numbers identified

by the board position numbers. (For example, the output and input numbers

supported by the I/O board in location 9 - 16 are as follows: A = 9, B = 10, C = 11,

D = 12, E = 13, F = 14, G = 15, and H = 16.)

Advertising