Extron Electronics Fiber Matrix 6400 - Manual (Page 81)

4-17 Fiber Matrix 6400 Switcher • Programmer’s Guide
Command/Response Table for IP-Specific SIS Commands
Symbol definitions
X3)
= Matrix name (Up to 240 alphanumeric characters)
N The following characters are invalid in the name: {space} ~ , @ = ` [ ] { } < > ‘ “ ; : | \ and ?.
X3!
= Default name Fiber-Matrix-64- + last 3 pairs of MAC address
X3@
= Time and date (for set) In the format: MM/DD/YY•HH:MM:SS where:
MM = month: 01 (January) through 12 (December)
DD = day: 01 through 31
YY = year: 00 through 99
HH = hour: 00 through 23
MM = minutes: 00 through 59
SS = seconds: 00 through 59
X3#
= Time and date (for read) In the format: Day,•DD•Mmm•YYYY•HH:MM:SS where:
Day = weekday: Mon through Sun
DD = date: 01 through 31
Mmm = month: Jan through Dec
YYYY = year: 2000 through 2099
HH = hour: 00 through 24
MM = minutes: 00 through 59
SS = seconds: 00 through 59
X3$
= GMT offset –12.0 through +14.0. Hours and minutes removed from GMT
X3%
= Daylight Saving Time 0 = Daylight Saving Time off/ignore
1 = Daylight Saving Time on (northern hemisphere)
2 = Daylight Saving Time on (Europe)
3 = Daylight Saving Time on (Brazil)
X3^
= IP address ###.###.###.###
X3&
= Hardware (MAC) address ##-##-##-##-##-##
X3*
= Number of open connections 0 – 255
X3(
= Password 12 alphanumeric characters
N The following characters are invalid in passwords: {space} + ~ , @ = ` [ ] { } < > ‘ “ ; : | \ and ?.
X4)
= Domain name Standard domain name rules apply (for example: xxx.com)
N The following characters are invalid in a domain name: {space} + ~ , = ` [ ] { } < > ‘ “ ; : | \ and ?. The @ character is acceptable only as
the lead-in to the domain name (such as @extron.com).
X4!
= E-mail account 65 - 72. 65 = e-mail recipient 1, 66 = 2, 67 = 3, ... 72 = recipient 8
X4@
= E-mail address Typical e-mail address format (for example: [email protected])
X4#
= Notification selections, part 1 I = inputs F = fans P = power supply
X4$
= Notification selections, part 2 If
X4#
= I, then
X4$
= 00 (all inputs), or 01 through 64 (input 1 through input 64)
If
X4#
= F, then
X4$
= 00 (both fans), 01 (fan 1), or 02 (fan 2)
If
X4#
= P, then
X4$
= 00 (both power supplies [PSs]), 01 (primary PS), or
02 (redundant PS)
X4%
= Notify when? 0 = no response 1 = fail/missing 2 = fixed/restored
3 = both 1 & 2 4 = suspend
X4^
= DHCP 0 =off, 1 = on
X4&
= Port # 00 (all ports), 01 (rear panel), 02 (front panel), 03 – 99
X4*
= Baud rate 9600, 19200, 38400, 115200
X4(
= Parity o dd, even, none, mark, space (Only the first letter required.)
X5)
= Data bits 7, 8
X5!
= Stop bits 1, 2
X5@
= Port type 0 = RS-232 1 = RS-422
X5#
= Verbose mode 0 = clear/none (default for Telnet connection)
1 = verbose mode (default for RS-232/RS-422 connection)
2 = tagged responses for queries
3 = verbose mode and tagged for queries
N If tagged responses is enabled, all read commands return the constant string and the value as the set command does
(for example, the read matrix name command
E
CN
}
, returns Ipn•
X3)]
).
X5$
= Port timeout interval (in 10-sec. increments) 1 (= 10 seconds) – 65000 (default is 30 = 300 seconds = 5 minutes)