Extron Electronics Fiber Matrix 6400 - Manual (Page 43)

3-17 Fiber Matrix 6400 Switcher • Operation
I/O grouping
I/O grouping is a matrix switcher feature that allows you to subdivide the front
panel controls of the matrix into up to four smaller functional sub-switchers
(figure 3-4) and limit tie creation from the front panel only. Inputs and outputs
can be assigned to one of four groups or not assigned to any group.
VSC 700 SCAN CONVERTER SIZE MIN/MAX NEXT MENU FREEZE
RESET IR
CENTER/PAN/SIZE
USP 405 UNIVERSAL SIGNAL PROCESSOR
ADJUST MENU
NEXT FREEZE 1 2 3 4 5
PICTURE ADJUSTMENTS CENTER SIZE BRT/CONT COL/TNT ZOOM DETAIL INPUTS RGB UNIVERSAL FREEZE COMPOSITE S-VIDEO SDI
1 2 3 4 5 6 7 8 9 10 11
17 18 19 20 21 22 23 24 25 26 27
33 34 35 36 37 38 39 40 41 42 43
49 50 51 52 53 54 55 56 57 58 59
1 2 3 4 5 6 7 8 9 10 11
17 18 19 20 21 22 23 24 25 26 27
33 34 35 36 37 38 39 40 41 42 43
49 50 51 52 53 54 55 56 57 58 59
1 2 3 4 5 6 7 8 9 10 11
INPUTS
INPUTS
17 18 19 20 21 22 23 24 25 26 27
33 34 35 36 37 38 39 40 41 42 43
49 50 51 52 53 54 55 56 57 58 59
1 2 3 4 5 6 7 8 9 10 11
17 18 19 20 21 22 23 24 25 26 27
33 34 35 36 37 38 39 40 41 42 43
49 50 51 52 53 54 55 56 57 58 59
1 2 3 4 5 6 7 8 9 10 11
17 18 19 20 21 22 23 24 25 26 27
33 34 35 36 37 38 39 40 41 42 43
49 50 51 52 53 54 55 56 57 58 59
1 2 3 4 5 6 7 8 9 10 11
17 18 19 20 21 22 23 24 25 26 27
33 34 35 36 37 38 39 40 41 42 43
49 50 51 52 53 54 55 56 57 58 59
OUTPUTS
OUTPUTS
4 input, 2 output
RGB video matrix
Computer #20
Monitor
Projector
Computer #17
Computer #3
Computer #26
Computer #24
Computer #3
3 input, 2 output
HD-SDI video matrix
VCR
DVD
Monitor
Monitor
Document Camera
Group 1
Group 2
Group
1
Group
2
Group
3
3 input, 4 output
DVI matrix
5
6
7
8
24 25 26
Input
Output
17 18 19
Input
1
2
20
Output
3
4
21 22 23
Input
Output
Group 3
Monitor
USP 405
All of the equipment in this figure
is connected through the appropriate
fiber optic transmitter or receiver. NOTE
Figure 3-4 — I/O grouping of incompatible video formats
When you are creating ties on the front panel, inputs and outputs that are assigned
to a group can be tied only to other outputs and inputs within the same group. For
example, a front panel operator cannot tie an input that is assigned to group 1 to an
output that is assigned to group 2. Ungrouped inputs and outputs can be switched
to outputs and inputs in any group. Ties between groups (an input in group 1 tied
to an output in group 2) can be created under RS-232/RS-422 or Ethernet control.