Climax BB6000 PORTABLE LINE BORING MACHINE - Manual (Page 8)

8 6/00
BB6000 Components
No. Description
Hydraulic motor fitting kit
Fitting kit to connect any hydraulic
motor listed above to the hoses from
customer's hydraulic power unit.
Fittings are included with every
Climax hydraulic power unit.
25492 Hydraulic motor fitting kit - 3/8"
fittings Fittings to connect motors
above to power units with 3/8"
female quick disconnect fittings.
Standard for 5 hp units
25495 Hydraulic motor fitting kit - 1/2"
fittings Fittings to connect motors
above to power units with 1/2"
female quick disconnect fittings.
Standard for 10 hp units.
End-mount bearing support
assembly
Bearing support assembly fits onto
the end of the work piece through a
slotted spider. Hold the bar in place
with the self-aligning bearing and
center the bar with the four adjusting
screws. At least two bearing
assemblies are required to
adequately support the bar. Different
styles may be used together.
22072 Three-arm end-mount bearing
support assembly, 20" (508.0 mm)
diameter
Bearing support assembly fits onto
the end of the work piece with
mounting diameters from 12.0" to
20.0" (304.8 to 508.0mm).
22091 Four-arm end-mount bearing
support assembly, 38" (965.2 mm)
diameter
Bearing support assembly fits onto
the end of the work piece with
mounting diameters from 18.0" to
38.0" (457.2 to 965.2 mm).
Support spider only
Because both end-mount bearing
assemblies use the same self-
aligning bearing, spiders can be
ordered separately to accommodate
various size work pieces.
22073 Three-arm support spider only
22092 Four-arm support spider only
Drawings may not represent product.
1 Included in component package 23222.
2 Included in component package 23223.
No. Description
ID-mount bearing support assembly
Bearing support assembly provides
four-way adjustable bar alignment.
Bar is held in place by a self-aligning
bearing. Center the bar by adjusting
the four jacking screws. At least two
bearing support assemblies are
required to adequately support the
bar. Different styles may be used
together.
23228 ID-mount bearing support
assembly, 22.53" (572.3mm) dia.
One bearing + two chucks + jaws to
fit inside bores with ID's from 12" to
22.53" (304.8 to 572.3mm)
23230 ID-mount bearing support
assembly, 37.53" (953.2mm) dia.
Same as above, but includes extra
spacer and jaws to fit inside bores
with ID's from 12" to 37.53" (304.8
to 953.2mm).
22377 1,2 Tool carrier
Split design tool carrier mounts
anywhere along the boring bar. Built-
in wipers protect the carrier and bar
from dirt and chips. Boring and
facing heads mount to the tool
carrier with screws and, if required,
spacers. Carrier includes axial
leadscrew nut. Customer must
purchase boring head set and tool
bits separately.
Boring head set
Boring heads mount to the tool
carrier (above) with screws and, if
required, spacers. The range of
diameters the boring head will cut is
determined by the number of
spacers mounted between the tool
carrier and the boring head. Small
tool holders use .5" (12mm) square
HSS tooling. Large tool holders use
1" (25.4mm) square HSS or
indexable carbide tooling. Customer
must purchase tool carrier and tool
bits separately.
22769 1 Boring head set, 6" -24" (152.4-
609.6 mm) ID
22383 2 Boring head set, 6"-36" (152.4 -
914.4mm) ID