Document Outline

• 1 Important Safety Instructions
• 2 Introduction
  • 2.1 Chapters summary
  • 2.2 Further information
• 3 Installation Overview
  • 3.1 Before installing the system
    • 3.1.1 Check the shipment
    • 3.1.2 Select locations for the system components
    • 3.1.3 Determine cabling and wiring scheme requirements
      • Wiring schemes
  • 3.2 Installing the Eclipse HX system
    • 3.2.1 Installing the matrix frame in a 19” rack
    • 3.2.2 Installing the cabling
    • 3.2.3 Connecting the other system components to the matrix frame
    • 3.2.4 Connecting to mains AC power
      • Eclipse HX matrix frames and interface frames (IMF-3)
      • I-Series panels
  • 3.3 After installing the Eclipse HX system
    • 3.3.1 Configuring the system with EHX software
    • 3.3.2 Minimum PC requirements (for EHX software)
    • 3.3.3 Recommended PC requirements (for EHX software)
    • 3.3.4 Checking the installed system
      • Checking the matrix frame
• 4 Locating System Components
  • 4.1 Locating Eclipse HX matrix frames
    • 4.1.1 Locating the Eclipse HX-Omega, Eclipse HX-Median and Eclipse HX-Delta
      • Cooling the Omega / Median matrix frame
      • Environmental information:
      • Cooling the Delta matrix frame
    • 4.1.2 Locating the Eclipse HX-PiCo
      • Cooling the matrix frame
  • 4.2 Locating interface frame(s) and power supplies
    • 4.2.1 IMF-3 interface frame
      • PSU-101 power supply for the IMF-3
      • IMF-3 rear panel
    • 4.2.2 IMF-102 interface frame
  • 4.3 Locating user panels
  • 4.4 Locating the external computer for EHX
• 5 Powering System Components
  • 5.1 Powering matrix frames
    • 5.1.1 Eclipse HX-Omega and Eclipse HX-Median
    • 5.1.2 Eclipse HX-Delta
    • 5.1.3 Eclipse HX-PiCo
  • 5.2 Powering user panels
    • 5.2.1 V-Series panels
    • 5.2.2 I-Series panels
  • 5.3 Powering interface frames
    • 5.3.1 IMF-3
      • PSU-101 alarm
    • 5.3.2 IMF-102
    • 5.3.3 Current capacities and consumption
• 6 Wiring System Components
  • 6.1 Using RJ-45 connectors
    • 6.1.1 Cabling standards
    • 6.1.2 Recommended cables, connectors and wiring tools
    • 6.1.3 Installing RJ-45 Connectors
  • 6.2 Connecting the matrix frame to a PC running EHX
    • 6.2.1 Ethernet connection to the PC
    • 6.2.2 Serial connection to the PC
      • Eclipse HX-Median, Eclipse HX-Omega and Eclipse HX-Delta
      • Eclipse HX-PiCo
  • 6.3 Connecting the matrix frame to an Ethernet network
  • 6.4 Connecting the matrix frame to a PC running Production Maestro Pro
    • 6.4.1 LMC-64 interface card
  • 6.5 Connecting the matrix frame to user panels
    • 6.5.1 4-Pair analog wiring
  • 6.6 General Purpose Outputs (GPOs)
  • 6.7 General Purpose Inputs (GPIs)
    • 6.7.1 Modes for General Purpose Inputs (GPIs)
      • Opto-isolated mode
      • Non-isolated mode
  • 6.8 E & M signalling with an E-QUE E1 / T1 interface card
    • 6.8.1 Example: Ship-to-shore satellite system
    • 6.8.2 Enabling E & M signaling on the E-QUE card
    • 6.8.3 Using the GPIs / GPOs to trigger actions
  • 6.9 Connecting the matrix frame to an external alarm
    • 6.9.1 Connecting to the alarm outputs of the PSU-101 power supply
  • 6.10 Connecting to a four-wire audio device
  • 6.11 Connecting to interface modules
    • 6.11.1 Wiring schemes for the FOR-22 interface module
      • External audio devices
      • Call Signal Input
      • Relay Contacts
    • 6.11.2 Wiring schemes for the CCI-22 interface module
    • 6.11.3 Wiring for Clear-Com analog partyline systems (including Encore)
      • Powering the CCI-22 interface module
      • Terminating the partyline channels
    • 6.11.4 Wiring schemes for TEL-14 interface modules
      • Wiring the TEL-14 interface to an IMF-3 interface frame
      • Wiring a TEL-14 interface to an IMF-102 interface frame
      • Connecting a TEL-14 interface to the telephone line
      • Using series-connected telephone sets with the TEL-14
      • Using relay contacts with the TEL-14 interface
    • 6.11.5 Wiring scheme for the RLY-6 interface module
      • Wiring the RLY-6 to an IMF-3 interface frame
      • Wiring external devices to an RLY-6 interface module
      • Wiring the RLY-6 to an IMF-102 interface frame
    • 6.11.6 Wiring schemes for a GPI-6 Interface module
      • Wiring the GPI-6 to the IMF-3 interface frame
      • Wiring the GPI-6 to external devices
      • Wiring the GPI-6 to an IMF-102 interface frame
• 7 Connecting Matrix Frames
  • 7.1 Intelligent linking
    • 7.1.1 Intelligent linking with trunk lines
    • 7.1.2 Serial port to serial port linking
  • 7.2 Linking Eclipse HX-Pico matrix frames with the PiCo-Link
  • 7.3 Tie-line (audio only) linking
  • 7.4 E1 / T1 linking
    • 7.4.1 E1 trunk connections
    • 7.4.2 T1 trunking
      • E1/T1 trunking failover
  • 7.5 Fiber-optic linking
• 8 Glossary