Gilderfluke&Co PA System - Manual (Page 27)

3) Half-mute a zone. Any of the eight possible half-mute zones can be activated by a but-
ton which has this function enabled. Any MA-100/200 output or DR-300/400 which has
been configured to respond to the requested half-mute zone will have itÕs audio level
lowered to whatever has been set as the half-muted level. A full mute will take prece-
dence over any half mutes active on the same outputs.
4) Toggle mute zone. This command will configure this button to toggle on and off the se-
lected mute zone each time it is pushed. Any MA-100/200 output or DR-100/300/400
which has been configured to respond to the requested mute zone will be muted. A full
mute will take precedence over any half mutes active on the same outputs.
5) Toggle half-mute zone. This command will configure this button to toggle on and off the
selected half-mute zone each time it is pushed. Any MA-100/200 output or DR-300/400
which has been configured to respond to the requested half-mute zone will have itÕs
audio level lowered to whatever has been set as the half-muted level. A full mute will
take precedence over any half-mutes active on the same outputs.
6) Rotate through mutes. This command will configure a button to half-mute a selected
zone on the first press, full mute it on the second press, and then remove both mutes on
the third. Any MA-100/200 output or DR-100/300/400 which has been configured to re-
spond to the requested mute zone will be muted. Any MA-100/200 output or DR-
300/400 which has been configured to respond to the requested half-mute zone will
have itÕs audio level lowered to whatever has been set as the half-muted level. A full
mute will take precedence over any half-mutes active on the same outputs.
7) Set volume zone to minimum. This will configure this button to set the selected volume
output to whatever has been set as itÕs minimum level each time it is pressed. What level
is used for the minimum is set in the MASTER CONFIGURATION menu. The level of the vol-
ume zone will be displayed on the LCD display when a key which uses this command is
invoked.
8) Set volume zone to maximum. This will configure this button to set the selected volume
output to whatever has been set as itÕs maximum level each time it is pressed. What level
is used for the maximum is set in the MASTER CONFIGURATION menu. The level of the
volume zone will be displayed on the LCD display when a key which uses this command
is invoked.
9) Lower volume zone output. This configures this button to ramp down the selected vol-
ume control zone as long as it is held in or until the minimum level for this volume zone
is reached. What level is used for the minimum is set in the MASTER CONFIGURATION
menu. A running count of the current volume zoneÕs level will be displayed on the LCD
display when a key which uses this command is invoked.
A) Raise volume zone output. This configures this button to ramp up the selected volume
control zone as long as it is held in or until the maximum level for this volume zone is
reached. What level is used for the maximum is set in the MASTER CONFIGURATION
menu. A running count of the current volume zoneÕs level will be displayed on the LCD
display when a key which uses this command is invoked.
B) Alternate direction of volume zone output. This configures this button to ramp up the
selected volume control zone on the first press, and ramp it down on the second press.
The ramping will continue as long as the button is held in or until the minimum or maxi-
mum levels for this volume zone are reached. What level is used for the minimum and
maximum levels are set in the MASTER CONFIGURATION menu. A running count of the
current volume zoneÕs level will be displayed on the LCD display when a key which uses
this command is invoked.
C) Repeater String. When this function is selected, then the string selected by the AUX.
STRING is sent to the Repeater port on the MA-100 when this button is pressed.
D) Terminal String. When this function is selected, then the string selected by the AUX.
STRING is sent to the Terminal port on the MA-100 when this button is pressed.
G ILDERFLUKE & C O . ¥ 205 S OUTH F LOWER S T . ¥ B URBANK , C ALIF . 91502-2102 ¥ 818/840-9484 ¥ FAX 818/840-9485
23 of 35