Yokogawa EJX115A - Manual (Page 64)

<9. Parameter Lists>
9-4
IM 01C25T04-01EN
Relative
Index
Index Parameter
Write
Mode
Initial Value Explanation
25 41 PROCESS_
CONNECTION_TYPE
O/S Unknown Index code for the material of the process connection. The
coding is in accordance to the Material Codes given in
teneral Requirements.
26 42 PROCESS_
CONNECTION_
MATERIAL
O/S Unknown Material code for the type of process connection. The index
code is manufacturer specific.
27 43 TEMPERATURE — — Temperature with the associated status used within the
transducer.
28 44 TEMPERATURE_
UNIT
O/S 1001: deg C The unit of the temperature.
29 45 SECONDARY_
VALUE_1
— — Pressure value and status available to the Function Block.
30 46 SECONDARY_
VALUE_1_UNIT
O/S kPa Pressure unit of the SECONDARY_VALUE_1
33 49 LIN_TYPE O/S 0: Linear Type of linearization
0: Linear
1: Linearization table
10: Square root
34 50 SCALE_IN AUTO — This is the input conversion using the high and low scale.
The related unit is the SECONDARY_VALUE_1_UNIT.
35 51 SCALE_OUT AUTO Output conversion of the linearized value using the high and
low scale. The related unit is the PRIMARY_VALUE_UNIT.
It is in accordance to the table of units codes given in the
general requirements.
36 52 LOW_FLOW_
CUTOFF
O/S 0 This is the point in percent of flow until the output of the flow
function is set to zero. It is used for suppressing low flow
values.
38 54 TAB_ACTUAL_
NUMBER
0 The actual numbers of entries in the table. It shall be
calculated after the transmission of the table is finished.
39 55 TAB_ENTRY O/S 0 This parameter identifies which element of the table is in the
TAB_X_Y_VALUE parameter currently
40 56 TAB_MAX_NUMBER 31 Maximum size of the table in the device
41 57 TAB_MIN_NUMBER 2 Minimum size of the table in the device
42 58 TAB_OP_CODE O/S 0: not initialized The modification of a table in a device influences the
measurement or actuation algorithms of the device. This
parameter is to control the transaction of the table.
43 59 TAB_STATUS — 0 Result of plausibility check in the device
44 60 TAB_X_Y_VALUE O/S One value couple of the table
59 75 PRIMARY_VALUE_
URL
— 100 Upper limit of primary value
60 76 PRIMARY_VALUE_
LRL
— -100 Lower limit of primary value
61 77 SENSOR_SN — Serial number of sensor
62 78 SENSOR_CAL_
METHOD
O/S 103: Factory trim
standard calibration
The method of the last sensor calibration
100= volumetric
101= static weight
102= dynamic weight
103= factory trim standard calibration
104= user trim standard calibration
105= factory trim special calibration
106= user trim special calibration
255= other
63 79 SENSOR_CAL_LOC O/S Space Set/indicate the location of the last sensor calibration
64 80 SENSOR_CAL_DATE O/S — Set/indicate the date of the last sensor calibration
65 81 SENSOR_CAL_WHO O/S Space Set/indicate the name of the person responsible for the last
sensor calibration
66 82 STATIC_PRESSURE_
HIGH_VALUE
— —
67 83 STATIC_PRESSURE_
UNIT
O/S kPa Unit of static pressure
68 84 CAL_DEVIATION_HI O/S 0 Deviation value for span adjustment
69 85 CAL_DEVIATION_LO O/S 0 Deviation value for zero adjustment
70 86 PRIMARY_VALUE_
FTIME
O/S 2 Damping time constant for primary value