Document Outline

• 1 Controls, Ports, and Indicators
  • Introduction
    • Front Panel
    • Additional Front Panel Controls and Indicators
    • Rear View
  • Applying Power to the HP Server
    • Powering-Up the HP Server
    • Powering-Down the HP Server
    • Connecting AC Power to Multiple-Server Configurations
• 2 Opening and Closing the HP Server
  • Introduction
  • Mounting the Front Bezel
  • Removing and Replacing the Front Bezel
  • Removing and Replacing the HP Server’s Main Cover
    • Tools Required
    • Removing the Top Cover
    • Replacing the Top Cover
• 3 Installing Fans and Power Supplies
  • Introduction
  • Tools and Supplies Needed
  • Hot Swapping the 172 mm Fans
    • Removing the 172 mm Fans
    • Installing the 172 mm Fans
  • Hot Swapping the 120 mm Fans
    • Removing the 120 mm Fans
    • Installing the 120 mm Fans
  • Hot Swapping Power Supplies
    • Determining Power Supply Status
    • Removing a Power Supply
    • Installing a Power Supply
• 4 Installing Mass Storage Devices
  • Introduction
  • Mass Storage Guidelines
    • Boot Priority
  • Tools Required
  • Installing a Hot Swap Hard Drive
    • Determining Drive Status
    • Removing a Hard Disk Drive
    • Installing a Hard Disk Drive
  • Installing Non-Hot Swap Drives
    • Installing the Floppy Disk Drive
    • Installing the DVD Drive
    • Connecting External SCSI Devices
  • Removing and Installing the Hard Disk Bay
    • Removing the Hard Disk Bay
    • Installing the Hard Disk Bay
  • Removing and Installing the SCSI Backplane
    • Removing the SCSI Backplane
    • Installing the SCSI Backplane Board
  • Installing the Front Panel Board
    • Removing the Front Panel Module
    • Installing the Front Panel Board
• 5 Installing Additional Memory
  • Introduction
    • Tools Required
    • Memory Installation Guidelines
  • Removing the Processor/Memory Complex
  • Removing the Memory Board DC-to-DC Converters
  • Removing and Installing Memory Boards
    • Removing Memory Boards
    • Installing Memory Boards
  • Installing and Removing DIMMs
    • Installing DIMMs
    • Removing DIMMs
  • Installing the Memory Board DC-to-DC Converters
  • Installing the Processor/Memory Complex
• 6 Installing an Additional Processor
  • Introduction
    • Tools Required
    • Processor Configuration Guidelines
  • Removing the CPU Thermal Dummy
  • Installing an Additional Processor
  • Firmware and Software Changes
    • Upgrading the Firmware
    • Reinstalling the NOS
  • Removing a Processor
  • Installing a CPU Thermal Dummy
  • Installing the Processor Baseboard
    • Removing the Processor Baseboard
    • Installing the Board in a System with Three or Four Microprocessors
    • Installing the Board in a System with Two Microprocessors
• 7 Installing Accessory Boards
  • Introduction
    • Tested PCI Boards
    • Tools Required
  • Accessory Board Installation Guidelines
    • IRQ Settings
    • Boot Priority
  • Installing Accessory Boards
    • Installing a Hot Swap PCI Board
    • Installing a Non-Hot Plug PCI Board
  • Removing Accessory Boards
    • Removing a Non-Hot Plug PCI Board
    • Removing a Hot Plug PCI Board
• 8 Server Management Boards
  • Introduction
    • Baseboard Management Controller (BMC)
    • Intelligent Chassis Management Bus (ICMB) Controller
    • Hot Swap Controller (HSC)
  • I/O Baseboard
    • Removing the I/O Baseboard
    • Installing the I/O Baseboard
  • Sideplane Board
    • Removing the Sideplane Board
    • Installing the Sideplane Board
  • PCI Hot Plug LED Board
    • Removing the PCI Hot Plug LED Board
    • Installing the PCI Hot Plug LED Board
  • Legacy I/O Board
    • Removing the Legacy I/O Board
    • Installing the Legacy I/O Board
  • Changing the Legacy I/O Board Battery
  • Power Distribution Board (T-Docking)
    • Removing the Power Distribution Board (T-Docking)
    • Installing the Power Distribution Board (T-Docking)
• 9 Connecting the Monitor, Keyboard, and Mouse
  • Introduction
• 10 Configuring the HP Server
  • Introduction
  • Configuring the HP Server
    • Power-on Sequence and Power-on Self Test (POST)
    • The Extensible Firmware Interface (EFI) Boot Manager
    • Server Management Configuration Utility
    • Using BIOS Setup
    • Using the SELViewer Utility
    • Using the SDR Viewer Utility
  • Upgrading the Server
    • Upgrading the BIOS by Using Iflash64
    • Upgrading the Firmware
    • Using the FRUSDR Load Utility
• 11 Troubleshooting
  • Introduction
  • Common Installation Problems
    • Troubleshooting Sequence
  • HP Server rx4610 SEL Data Tables
    • HP Server rx4610 Generator ID Codes
  • BIOS Error Codes\Messages
  • Beep Codes
    • Beep Codes and Interpretation
  • Types of Memory Tests
    • First Row Memory Test
    • Base Memory Test
    • Extended Memory Test
    • Memory Test Duration
    • Aborting the Memory Test
    • Setup Dialog
    • Memory Testing Error Codes\Messages
• A Specifications
  • Introduction
    • Requirements
    • Video Display Modes
  • Connector Pinouts and Boardset Locations
    • VGA Video Port
    • Keyboard and Mouse
    • Parallel Port
    • Serial Ports A and B
    • Universal Serial Bus (USB)
    • SCSI
    • IDE
    • PCI
  • Information on Jumpers
    • General Procedure to Change Jumper Settings
    • Processor Baseboard Jumpers
    • Legacy I/O Board Jumpers
    • I/O Baseboard Jumpers
    • Power Distribution Board Jumpers (T-Docking)
    • Determining DC-to-DC Status
• B Equipment Log and Configuration Worksheet
  • Equipment Log
• C INI File Format
  • Introduction
    • INI File Structure
    • Data Markers
• Index