Document Outline

• APP1.pdf
  • 1. ANALOGUE OUTPUT COMMANDS
    • • AMODE Setting the analogue outputs
      • ASEL Scaling the analogue outputs
      • ASCL Scaling the analogue outputs
  • 2. CALIBRATION COMMANDS
    • • CRH Relative humidity calibration
      • FCRH Relative humidity calibration after sensor change
      • CT Temperature calibration
      • ACAL Calibrating the analogue outputs
      • L Outputting linear correction coefficients
      • LI Entering linear correction coefficients
  • 3. OUTPUT VIA THE SERIAL BUS
    • • R Starting the measurement output
      • S Stopping the measurement output
      • SEND Outputting a reading once
      • DSEND Outputting readings of all connected transmitters once
      • ERRS Outputting error messages
      • ECHO Turning the serial interface echo ON/OFF
      • INTV Setting the output interval for the RUN state
      • FORM Setting the output format
      • FTIME Adding time to output
      • FDATE Adding date to output
      • SERI Serial bus settings
      • UNIT Selecting the output units
      • ADDR Setting the transmitter address
      • FROST Setting the calculation mode
      • RESET Resetting the transmitter
    • 3.1 Operation modes
      • SMODE Setting the serial interface
      • OPEN & CLOSE
  • 4. OTHERS
    • • ITEST Testing the analogue outputs
      • FILT Setting the averaging time
      • PRES Setting the pressure for pressure compensation of the HUMICAP( sensor and for mixing ratio, wet bulb temperature and enthalpy calculations
      • XPRES Setting the pressure for pressure compensation of the HUMICAP( sensor and mixing ratio, wet bulb temperature and enthalpy calculations tempo˜rarily
      • CDATE Entering calibration date
      • DATE Setting the date
      • TIME Setting the time
      • VERS Name and version of the programme
      • ? Outputting the transmitter settings
      • ?? Outputting the transmitter settings also in POLL mode
• APP2.pdf
  • INSTALLING THE POWER SUPPLY MODULE
  • TECHNICAL SPECIFICATIONS
• APP3.pdf
  • 1. INSTALLATION
  • 2. OPERATION
  • 3. NETWORK CONFIGURATION
    • Single loop operation
    • Dual loop operation
  • 4. CHECKING THE SERIAL PORT NETWORK OPERATION
    • STOP mode
    • POLL mode
    • RS 485 network settings
  • 5. SPECIFICATIONS
• APP4.pdf
  • 1. INSTALLATION
  • 2. OPERATION
  • 3. NETWORK CONFIGURATION
    • Single loop operation
    • Single loop wiring
    • Dual loop operation
    • Dual loop wiring
  • 4. CHECKING THE SERIAL PORT NETWORK OPERATION
    • STOP mode
    • POLL mode
    • Current loop settings
  • 5. SPECIFICATIONS
• APP5.pdf
  • 1. ERROR TYPES
    • 1.1 Errors after reset
    • 1.2 Errors during operation
• APP7.pdf
  • ALARM OUTPUT UNIT
    • • • Setting and activating the outputs with menu commands
      • Setting and activating the outputs using an RS line
• APP8.pdf
  • 1.1 Connector options 141
  • 1.2 Analogue outputs
  • 1.3 Serial connections
  • 1.4 Instructions for connecting and mounting the counter pieces
• APP9.pdf
  • GENERAL
  • TO BE NOTED IN RE-GAINING
  • LED COMMANDS
  • DISPLAY/KEYPAD COMMANDS
    • Re-gaining parameters
    • Starting re-gaining manually
  • SERIAL COMMANDS
    • • REG Re-gaining settings
      • CR Re-gaining parameters
      • CRI Changing re-gaining parameters
      • FST Displaying re-gaining status
      • REGEN Starting re-gaining manually
  • TECHNICAL DATA
• APP10.pdf
  • PRESSURE UNIT CONVERSION CHART
• App 11.pdf
  • APPENDIX 11
  • WIRING DIAGRAM
• Warranty.pdf
  • Warranty
• Warranty.pdf
  • Warranty