Avaya PARTNER-18D - Manual (Page 94)

System Flow Chart–System
System Date
Dial # 1 0 1
Dial the date (MMDDYY)
System
Day
Dial # 1 0 2
Dial 1=Sun ✔
2=Mon 3-Tue, 4=Wed, 5=Thur,
6=Fri, 7=Sat
System Time
Dial # 1 0 3
Dial the time (HHMM-24 hr. military
time)
Number of Lines
Dial # 1 0 4
Dial two digits (01–31) (R. 4.0) or,
Dial two digits (01–19 (Prior R. 4.0),
for # of outside lines assigned to
every extension. 3 per ACS
processor & 308EC module. 16 for
1600DSL module. 2 per 206 or 200
module ✔. 4 per 400EC module ✔.
WARNING
Do not use Number of Lines (#104) after
initial setup. In Key mode, the Number of
lines procedure will change Line
Assignment (#301), Line Access
Restriction (#302), Automatic Line
Selection and Line Ringing to factory
settings.
To change line assignments without
affecting other settings, use Line
Assignment (#301).
In Hybrid mode, the Number of Lines
procedure will change Pool Line
Assignment (#207), Pool Extension
Assignment (#314), and Pool Access
Restriction (#315). Additionally, it
changes Line Assignment (#301), Line
Access Restriction (#302), Automatic
Line Selection and Line Ringing. To
change pool assignments without
affecting other settings, use Pool Line
Assignment (#207) and Pool Extension
Assignment (#314).
Transfer Return Rings
Dial # 1 0 5
Dial 1 digit (0–9) for # of rings before
call returns.
0–9 rings
4 rings
✔
0 rings=no return
Recall Timer Durations
Dial # 1 0 7
Dial two digits (01–80) to set length
of a switchook flash ✔=18 (450
msec)
Rotary Dialing Timeout
Dial # 1 0 8
Dial 1=4 secs
2=8 secs ✔
3=12 secs
Outside Conference Denial
Dial # 1 0 9
Dial 1=Allowed ✔
2=Disallowed
Automatic System Answer Delay
Dial # 1 1 0
Dial a ring delay number (0–9)
2 rings ✔
Direct Extension Dial Delay
Dial # 1 1 2
Dial a ring delay number (0–9)
2 rings ✔,
0 rings=answered immediately
Automatic System Answer Button
Dial # 1 1 1
Dial 1=Assigned,
2=Not Assigned ✔
3=Select Button then press a
programmable button
Direct Extension Dial Button
Dial # 1 1 3
Dial 1=Assigned
2=Not Assigned ✔
3=Select Button then press a
programmable button
Outgoing Call
Restriction Button
Dial
# 1 1 4
Dial 1=Assigned
2=Not Assigned ✔
3=Select Button then press a
programmable button
Wake Up Service Button
Dial # 1 1 5
Dial 1=Assigned
2=Not Assigned ✔
3=Select Button then press a
programmable button
VMS Cover Rings
Dial # 1 1 7
Dial 1–9
3 ✔
Ring On Transfer
Dial # 1 1 9
Dial 1=Active ✔
2=Not Active
Automatic System Answer Mode
Dial # 1 2 1
Dial 1=Hold ✔
2=Disconnect
3=Ring
Caller ID Type
Dial # 1 2 2
Dial 1=USA ✔
2=Singapore
Backup Programming Automatic
Dial # 1 2 3
Dial 1=Active
2=Not Active ✔
3=Backup Alarm Cleared
Backup Programming—Manual
Dial
# 1 2 4
Press e to begin the backup
Automatic Daylight/
Standard Times
Dial
# 1 2 6
Dial 1=Active ✔
2=Not Active
2.0 or earlier
2.0
2.0
2.0
2.0
System Reset—Programming Saved
IMPORTANT: Using this procedure disconnects any active calls but
retains system settings. Use it only if the system fails to function
correctly after a power failure or down period. Dial # 7 2 8 .
Restore Programming
Dial # 1 2 5
Dial 1=MAN.mmddyy ✔
2=AUTO.mmddyy
Press e to begin the restore
Mode of Operation
Press f 0 0 s
s # 1 9 8
Enter the system password
Dial 1=Key (factory setting)
✔
2=Hybrid
Call Coverage Rings
Dial # 1 1 6
Dial 1–9
2 ✔
2.0
3.0