Réglages / settings / einstellungen – Sulky Xeos HD User Manual
Page 53
51
- Check the new setting by carrying out another
calibration test.
Once the setting has been fixed, lift the
shutter lever
again and replace the
locking pin.
E
.
G
.:
Drilling wheat at 180 kg / ha Setting value
according to chart = 65
1st test gives, for example: 4 kg for 1/40 ha
(4x40=160 kg/ha)
This is around 12% less in comparison with the
indicative value of 4.50kg for 1/40 ha
- Increase the setting by 12%, i.e. to 73.
- Validate the new setting by turning the crank
handle again then weighing the amount collected.
Note:
In micro position, if the marker is set to higher than 50
with small seed, it is possible to return to normal
position.
I
N
THIS
CASE
,
THE
MARKER
POSITION
SHOULD
BE
DIVIDED
BY
5.
This will improve the position in the row via a higher
metering mechanism rotation speed.
The screen should always be in place in the
hopper when carrying out a calibration test.
1
1
- Neue Einstellung durch eine weitere
Abdrehprobe bestätigen.
Wenn die Aussaatmenge eingestellt ist, den
Hebel des Schiebers
hochstellen und mit
dem Splint verriegeln.
B
EISPIEL
:
Weizen mit 180 kg/ha aussäen, Einstellwert der
Tabelle = 65.
1. Abdrehprobe ergibt z. B.: 4 kg für 1/40 ha
(4x40=160 Kg/ha)
Das macht etwa 12% weniger als der Richtwert
von 4,50kg /ha für 1/40.
- Einstellung um 12 % erhöhen, also 73.
- Neue Einstellung bestätigen durch erneutes
Drehen mit der Kurbel und Wiegen der ausgesäten
Menge.
Anmerkung:
Wenn bei kleinen Saatkörnern die Marke in Position
Mikrogeschwindigkeit auf über 50 steht, kann auf
Normalgeschwindigkeit umgestellt werden.
I
N
DIESEM
F
ALL
DIE
P
OSITION
DER
M
ARKE
DURCH
5
DIVIDIEREN
.
Dies verbessert die Position in der Reihe durch eine
höhere Rotationsgeschwindigkeit des Dosierers.
Das Sieb muss bei den Abdrehproben stets
im Tank sein.
1
1
A
A
FR
GB
DE
Réglages / Settings / Einstellungen
A
A
A
- Valider le nouveau réglage par un autre essai de
débit.
Une fois le débit réglé, remonter le levier de
trappe
et le verrouiller avec sa goupille.
E
XEMPLE
:
Semer du blй а 180 Kg/ha
Valeur de réglage selon tableau = 65
1er essai donne par ex : 4 Kg pour 1/40 ha
(4x40 = 160 Kg/ha)
Cela fait environ 12% de moins par rapport à la
valeur indicative de 4,50kg /ha pour 1/40.
- Augmenter de 12% le réglage soit 73.
- Valider le nouveau réglage en refaisant les tours
de manivelle puis en pesant la quantité
récupérée.
Note:
En positon Micro, si le repère est sur une position
supérieure à 50 avec des graines de petites tailles, il
est possible de repasser en position normale.
D
ANS
CE
CAS
,
IL
FAUT
DIVISER
LA
POSITION
DU
REPÈRE
PAR
5.
Cela améliore la position sur le rang par une vitesse
de rotation supérieure du doseur.
Le tamis doit toujours être en place dans la
trémie, lors des essais de débit.
1
1
1
3