Tweco 200 XT Ultra-Cut Plasma Cutting System User Manual
Operating manual, Ultra-cut 200 xt, Plasma cutting system
Advertising
Table of contents
Document Outline
- SECTION 1: GENERAL INFORMATION
- SECTION 2: SPECIFICATIONS
- 2.01 General Description Of The System
- 2.02 Plasma Power Supply
- 2.03 Remote Arc Starter
- 2.04 Gas Control Module
- 2.05 Precision Plasma Cutting Torch
- 2.06 Specifications & Electrical Requirements
- 2.07 Power Supply Dimensions
- 2.08 Power Supply Rear Panel Features
- 2.09 Gas Requirements
- 2.10 Gas Applications
- 2.11 XT Torch Specifications
- SECTION 3: INSTALLATION
- 3.01 Installation Requirements
- 3.02 System Layout
- 3.03 Recommended Gas Supply Hose
- 3.04 Leads and Cables All Amperage
- 3.05 Lift the Power Supply
- 3.06 Connect Input Power and Ground Cables
- 3.07 Connect Work Cable and Pilot and Negative Leads
- 3.08 Ground Connections
- 3.09 Connect Coolant Leads
- 3.10 Connect Cables for CNC, Remote Arc Starter, GCM and HE 400
- 3.11 Handling and Installation of Fiber Optics
- 3.12 Set Switches on the Command - Control Module
- 3.13 Height Control Connections
- 3.14 Gas Control Module Installation
- 3.15 Fiber Optic Cable Installation
- 3.16 Gas Control Module: Control, Input, and Output Connections
- 3.17 Optional HE400 COOLER
- 3.18 Install Remote Arc Starter
- 3.19 Torch Valve Installation
- 3.20 Connecting Torch
- 3.21 Install Consumable Torch Parts
- 3.22 Voltage Divider for iHC Torch Height Control
- 3.23 Complete the Installation
- SECTION 4: OPERATION
- SECTION 5: MAINTENANCE
- SECTION 6: REPLACEMENT ASSEMBLIES & PARTS
- 6.01 Replacement Power Supply
- 6.02 System Layout
- 6.03 Recommended Gas Supply Hose
- 6.04 Leads And Cables All Amperages
- 6.05 Power Supply External Replacement Parts
- 6.06 Power Supply Replacement Parts - Upper Right Side
- 6.07 Power Supply Replacement Parts - Lower Right Side
- 6.08 Power Supply Replacement Parts - Rear Panel
- 6.09 Power Supply Replacement Parts - Left Side
- 6.10 Gas Control Module (GCM-2010) Replacement Parts
- 6.11 Gas Control Module (GCM-2010) Replacement Parts
- 6.12 Remote Arc Starter (RAS-1000 XT) Replacement Parts
- 6.13 HE 400 Heat Exchanger - Replacement Parts
- SECTION 7: TORCH MAINTENANCE
- APPENDIX 1: Remote Arc Starter Schematic
- APPENDIX 2: Gas Control and Torch Valve Schematic
- APPENDIX 3: Gas Control Module Plumbing Diagram
- APPENDIX 4: Gas Control Module PCB Layout
- APPENDIX 5: Gas Control Display Module PCB Layout
- APPENDIX 6: CNC - Control Module PCB Connections
- APPENDIX 7: CNC
- Appendix 8: CCM CPU PCB Layout
- Appendix 9: CCM I/O PCB Layout
- Appendix 10: Pilot PCB Layout
- Appendix 11: Relay and Interface PCB Layout
- Appendix 12: Display PCB Layout
- Appendix 13: System Bias PCB Layout
- Appendix 14: Main Inverter Bottom PCB Layout
- Appendix 15: Main Inverter Top PCB Layout
- Appendix 16: Control and Fault PCB Layout
- Appendix 17: Cap Bias Bottom PCB Layout
- Appendix 18: Cap Bias Top PCB Layout
- Appendix 19: Suppressor PCB Layout
- Appendix 20: COOLING DIAGRAM
- APPENDIX 21: System Schematic 200A, 480V PG 1
- APPENDIX 22: System Schematic 200A, 480V PG 2
- Appendix 23: ADVANCED TROUBLESHOOTING
- APPENDIX 24: PUBLICATION HISTORY