Great Plains 30-Foot High Clearance Full Press Drill 1983-1985 Parts Manual - Manual (Page 87)

Revision Comments Part Description Part No. Ref.
Image No. dwg18210
Shown 10 OPENER PIVOT TB ASS'Y LH 129-011H 1.
10 OPENER PIVOT TB ASS'Y RH 129-012H 1.
12 OPENER PIVOT TB ASS'Y LH 129-013H 1.
12 OPENER PIVOT TB ASS'Y RH 129-014H 1.
HALF CLAMP 105-029D 2.
HHCS 1/2-13X1 1/4 GR5 802-034C 3.
WASHER LOCK SPRING 1/2 PLT 804-015C 4.
NUT HEX 1/2-13 PLT 803-020C 5.
2nd rev. 1984 and 1985 HHCS 5/8-11X2 GR5 802-055C 6.
1st rev. 1983 PIN CLEVIS 5/8 X 1 33/64 USBLG 805-071C 6.
1st rev. 1983 REPL. BY 805-071C 109-054H 6.
2nd rev. 1984 and 1985 NUT LOCK 5/8-11 PLT 803-024C 7.
1st rev. 1983 WASHER FLAT 5/8 SAE PLT 804-021C 7.
PIN CLEVIS 3/4 X 3 1/2 USABLLG 805-047C 8.
WASHER FLAT 3/4 SAE PLT 804-025C 9.
PIN COTTER 3/16 X 1 1/4 PLT 805-016C 10.
TOP WIND OPENER FRAME JACK 890-075C 11.
HC JACK SUPPORT PLATE 129-017D 12.
HC OPENER JACK SUPPORT 129-016D 13.
OPENER FRAME GAUGE 129-023D 14.
HHCS 5/8-11X2 GR5 802-055C 15.
WASHER LOCK SPRING 5/8 PLT 804-022C 16.
NUT HEX 5/8-11 PLT 803-021C 17.
PIVOT ANGLE WLDM'T RH 132-060H 18.
U-BOLT 5/8-11 X 4 X 5 1/4 806-008C 19.
PIVOT ANGLE WLDM'T LH 132-061H 20.
PIVOT BAR 131-007D 21.
12" spacing, center box inside left,
inside right.
PULL ARM 105-030D 21.
HOE TRUNNION 132-107D 22.
PIVOT BAR COLLAR 132-108D 23.
PIN SPIRAL 5/16 X 1 1/4 PLAIN 805-055C 24.
Not shown. Use with item 6 -
109-054H or 805-071C.
PIN COTTER 5/32 X 1 PLT 805-019C 25.
ADJUSTER BOLT 132-106D 26.
NUT HEX SLOTTED 5/8-11 PLT GR5 803-056C 27.
HC HOE FRAME LEFT & CENTER 10 132-001H 28.
Shown ST HOE FRAME RH 10 132-026H 28.
HC HOE FRAME LEFT & CENTER 12 132-002H 28.
ST HOE FRAME RH 12 132-027H 28.
12/26/12 - 87 - 129-035P
Table of Contents Part Number Index
Openers and Opener Frames
Pivot Tube Assembly - Spring Trip Hoe Opener Frame (1983 <-> 1985)
(Applies to HCF30 (1980-1985) only)