Dell PowerEdge 6850 - Manual (Page 27)

The LCD can display two lines of alphanumeric characters. The display codes are presented in two color combinations:
l Blue background — Information only; no action is required.
l Amber background — The system needs attention.
Table 2 -7 lists the LCD status messages that can occur and the probable cause for each message. The LCD messages refer to events recorded in the system
event log (SEL). For information on the SEL and configuring system management settings, see the systems management software documentation.
Table 2-7. LCD Status Messages
CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as
authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not
authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product.
Line 1
Message Line 2
Message Causes Corrective Actions
SYSTEM
ID
SYSTEM NAME SYSTEM ID is a unique name, five
characters or less, defined by the user.
SYSTEM NAME is a unique name, 16
characters or less, defined by the user.
The system ID and name display under the
following conditions:
l The system is powered on.
l The power is off and active POST
errors are displayed.
This message is for information only.
You can change the system ID and name in the System Setup program. See your
User's Guide for instructions.
E0000 OVRFLW CHECK
LOG
LCD overflow message.
A maximum of three error messages can
display sequentially on the LCD. The fourth
message displays as the standard overflow
message.
Check the SEL for details on the events.
E0119 TEMP AMBIENT
TEMP BMC
Ambient system temperature is out of
acceptable range. See " Troubleshooting System Cooling Problems " in "Troubleshooting Your System."
E0212 VOLT PG n System power supply is out of acceptable
voltage range; faulty or improperly
installed power supply. See " Troubleshooting Power Supplies " in "Troubleshooting Your System."
E0212 VOLT BATT
ROMB
Faulty RAID battery. Replace the RAID battery. See " Activating the Optional Integrated RAID Controller " in
"Installing Drives."
E0212 VOLT BATT
CMOS
Faulty system battery. See " Troubleshooting the System Battery " in "Troubleshooting Your System." If the
problem persists, see " Getting Help ."
E0412 RPM FAN n
FAN
REDUNDANCY
LOST
Specified cooling fan is faulty, improperly
installed, or missing. See " Troubleshooting System Cooling Problems " in "Troubleshooting Your System."
E0780 PROC n
PRESENCE
Microprocessor is not installed in socket n. Install a microprocessor in socket n. See " Installing a Processor " in "Installing System
Components."
E07F0 PROC n IERR Faulty or improperly installed
microprocessor. See " Troubleshooting the Microprocessors " in "Troubleshooting Your System."
E07FA PROC n
THERMTRIP
Specified microprocessor is out of
acceptable temperature range and has
halted operation. See " Troubleshooting System Cooling Problems " in "Troubleshooting Your System." If
the problem persists, ensure that the microprocessor heat sinks are properly
installed. See "
Removing a Processor " in "Installing System Components."
NOTE: The LCD continues to display this message until the system's power cord is
disconnected and reconnected to the AC power source, or the SEL is cleared using
either Server Assistant or the BMC Management Utility. See the Dell OpenManage
Baseboard Management Controller User's Guide for information about these utilities.
E0876 PS n MISSING
PS n STATUS
No power available from the specified
power supply; specified power supply is
improperly installed or faulty. See " Troubleshooting Power Supplies " in "Troubleshooting Your System."
E0876 PS n
PREDICTIVE
Power supply voltage is out of acceptable
range; specified power supply is improperly
installed or faulty. See " Troubleshooting Power Supplies " in "Troubleshooting Your System."
E0876 PS n AC LOST
PS n AC
RANGE
Power source for specified power supply is
unavailable, or out of acceptable range. Check the AC power source for the specified power supply.
E0D76 BP DRIVE n
1x2 DRIVE
FAIL n
SCSI
CONNECTOR
Faulty or improperly installed hard drive or
RAID controller. See " Troubleshooting SCSI Hard Drives " " Troubleshooting a RAID Controller Card , "
and " Troubleshooting the Integrated RAID Controller " in "Troubleshooting Your
System."