Two Brothers Racing 2006-07 Suzuki GSX-R600/750 User Manual

V.a.l.e, Juice box™ - fuel controller, Two brothers racing

background image

Two Brothers Racing

Juice Box™ - Fuel Controller

2006-07 Suzuki GSX-R600/750 Installation & Operation Manual

Part # 008-147-6C / 008-147-7C

Parts Incuded

Installation Instructions



Part Number


Juice Box™ Fuel Control Kit

008-147-6/7C (#9140061C) / (#9140063C)


Zip Ties


Adhesive Velcro Square


V a r i a b l e a x i s l o c k i n g e x h a u s t


The JUICE BOX™ can be mounted under the rear

passenger seat or near the gauge pod at the front of the

bike. If the desired mounting location is under the rear

passenger seat, the JUICE BOX™ wire harness should

be routed starting from under the rear seat, then under

the front seat and under the tank hinge to the rear of the

engine. If the desired mounting location is at the front of

the bike, skip this step.

This bike has primary (lower) and secondary (upper)

injectors. Locate primary (lower) injector connectors

under tank, to the rear of the air box on the throttle bodies

and under the fuel rail. DO NOT connect the TBR Juice

Box to the secondary (upper) injectors. (Fig 5)

Disconnect stock injector (one at a time) and connect

the JUICE BOX™ gray connector to bike’s injector then

connect stock injector connector to Juice Box’s black

connector. Repeat for the remaining 3 cyl’s. (Fig 6)

Route black ground wire from JUICE BOX™ to crank case

breather vapor separator. Remove just 1 mounting bolt

and attach JUICE BOX™ black ground wire to bolt and

tighten bolt. (Fig 7)







two brothers racing warrants that this product carries a warranty for 2 years from date of purchase against original

defects in materials and workmanship. should this product fail to perform for either of the above reasons, two brothers

racing will repair or replace it with an equivalent product at no charge, except for postage, to the original retail purchaser.

to obtain the benefits of this warranty, the retail purchaser must return the product and proof of purchase to the place of

original purchase.

We recommend that this performance part be installed by a qualified motorcycle

technician. If you have any doubts as to your ability to install this performance part,

please consult with your local motorcycle dealer. Read all instructions first before

starting installation. Make sure the vehicle and exhaust system are completely cool

before starting the installation. Also, make sure the vehicle is secure during installation.

Be sure to save all stock components for possible use later.

This Juice Box is legal for use on Emissions Controlled street and highway vehicles.

The Juice Box™ is not applicable, nor inteded for use on aircraft.

Thank you for purchasing a genuine Two Brothers Racing

JUICE BOX™. This product represents a radical step

forward in tuning fuel-injected motorcycles and ATVs for

optimal performance using “load-based” technology.

We at Two Brothers Racing hope that you will find this

development as exciting and useful as we do. And

remember: Proper Fuel = Maximum Power!

Make sure the vehicle is completely cool before starting

the installation. Also, make sure the vehicle is secure and

will not roll around.

Remove 2 bolts (1 right side and 1 left side) that secure

tank side panels and front seat in place. (Fig 1)

Remove front rider seat, exposing battery. (Fig 2)

Remove right and left tank side panels by pulling gently

out and to the rear of the bike. (Fig 3)

Remove 1 bolt that secures gas tank to frame near triple

tree. (Fig 4a) Lift gas tank up and support with tank

support rod found in rear passenger seat compartment.

(Fig 4b)






Tools Needed For Install

- 8mm Wrench
- 5mm, 6mm Allen Wrench

Continued on page 2

Fig 1

Fig 2

Fig 3

Fig 4a

Fig 4b

Fig 5

Fig 6

Fig 7