Two Brothers Racing Yamaha Raptor 700 - Manual

Two Brothers Racing
Juice Box™ - Fuel Controller
2006-08 Yamaha Raptor 700 Installation & Operation Manual
Part # 008-138
Parts Incuded
Installation Instructions
Qty. Description Part Number
1 Juice Box™ Fuel Control Kit 008-138
3 Zip Ties
1 Adhesive Velcro Square
V.A.L.E.
V a r i a b l e a x i s l o c k i n g e x h a u s t
TM
Remove the stock fuel injector connector at the fuel
injector (Figure 5).
Route the JUICE BOX™ wires under the gas tank frame
mount and up towards the fuel injector. (The aluminum
mount just above the battery (-) negative terminal on the
left side of the machine.)
Snap the female connector into the fuel injector. Snap
the original connector removed from the fuel injector
into the JUICE BOX™ male connector (Figure 6).
Remove the (-) battery terminal bolt and place ground
wire above the stock (-) terminal and re- install the (-)
terminal bolt (figure 7).
For tuning purposes you may want to keep the JUICE
BOX™ where you can reach it. Once you get things
dialed in, route the JUICE BOX™ wire harness under the
battery mount and the two air box mounting tabs then
secure the harness to the frame with zip ties. The JUICE
BOX™ will easily fit in the rear toolbox area with the
supplied Velcro pad. (Figure 8)
7.
8.
9.
10.
11.
IMPORTANT - PLEASE READ CAREFULLY
Warranty
two brothers racing warrants that this product carries a warranty for 2 years from date of purchase against original
defects in materials and workmanship. should this product fail to perform for either of the above reasons, two brothers
racing will repair or replace it with an equivalent product at no charge, except for postage, to the original retail purchaser.
to obtain the benefits of this warranty, the retail purchaser must return the product and proof of purchase to the place of
original purchase.
We recommend that this performance part be installed by a qualified ATV technician. If
you have any doubts as to your ability to install this performance part, please consult
with your local ATV dealer. Read all instructions first before starting installation. Make
sure the vehicle and exhaust system are completely cool before starting the installation.
Also, make sure the vehicle is secure during installation. Be sure to save all stock
components for possible use later.
The Juice Box™ is legal ONLY for closed course race vehicles. The Juice Box™ is not
applicable, nor inteded for use on EMISSIONS CONTROLLED street, highway or off-road
vehicles. The Juice Box™ is not applicable, nor inteded for use on aircraft.
Thank you for purchasing a genuine Two Brothers Racing
JUICE BOX™. This product represents a radical step
forward in tuning fuel-injected motorcycles and ATVs for
optimal performance using “load-based” technology.
We at Two Brothers Racing hope that you will find this
development as exciting and useful as we do. And
remember: Proper Fuel = Maximum Power!
Make sure the vehicle is completely cool before starting
the installation. Also, make sure the vehicle is secure and
will not roll around.
Remove the seat.
Remove the radiator cover bolts. (Figure 1). Remove the
gas cap and gas tank cover. NOTE: replace the gas cap as
soon as the gas tank cover is removed.
Remove the 2 bolts holding the side panels and 2 plastic
screws (Figure 2).
Remove the 2 fuel tank mounting bolts and 2 plastic
screws that are holding the rubber flap (Figure 3).
Lift the tank up; you do not need to remove it (Figure 4)
and support with foam block from TBR exhaust packaging.
1.
2.
3.
4.
5.
6.
Tools Needed For Install
- #2 Phillips Screwdriver
- 10mm Wrench
- 4mm Allen Wrench
Operation Manual on page 2
Fig 1
Fig 2
Fig 3
Fig 41
Fig 5
Fig 6
Fig 7
Fig 8