KEYENCE CZ-V1 - Manual

1
RGB Digital Fiberoptic Sensors
CZ Series
Instruction Manual
SAFETY PRECAUTIONS
This manual describes the instructions, operating procedures and
precautions for using the CZ Series.
Before beginning operation, please read this manual carefully to get the
most from your CZ Series.
Keep this manual handy for future reference.
• The CZ Series is intended for the detection of target objects. Do
not use the CZ Series in a safety circuit to protect the human
body.
• The CZ Series does not have an explosion-proof structure. Do
not use it in a location where any flammable gases, liquid or
powder exist.
ACCESSORIES
WARNING
SPECIFICATIONS
Model
Light source
Response time
Indicators
Error indication
Calibration method
Tolerance value
adjustment
Differentiation mode
Timer function
Output mode
selection
External synchro-
nization input
External calibration
input
Registered color
selection
Control output
Protection circuit
Power supply
Current
consumption
Ambient light
Ambient
temperature
1.
Relative humidity
Vibration
Shock
Housing material
Weight (including
2 m cable)
CZ-V1
Red LED, Green LED, Blue LED
300 µs/1 ms (switch selectable)
Output: Red LED, Calibration: Orange LED,
External synchronization input: Green LED,
Matching rate/received light intensity: LCD (Red/Green)
Excess light intensity, insufficient light intensity,
insufficient color difference
1-point/2-point calibration (switch selectable)
Numerical value setting on digital display
C mode/C + I mode/I mode (switch selectable)
Timer OFF/OFF-delay timer (40 ms) (switch selectable)
Match output: Turns on when target color
matches registered color.
Mismatch output: Turns on when target color is different
from registered color. (switch selectable)
Response speed: 500 µs max.
Input response time: 20 ms min.
8-bank selection (By external input or key operation),
Input response time: 20 ms min.
NPN open-collector: 40 VDC max. (100 mA max.),
Residual voltage: 1.0 V max.
Reverse-polarity protection (power supply),
overcurrent protection (output), surge protection (output)
12 to 24 VDC ±10%, Ripple (P-P): 10% max.
75 mA max.
Incandescent lamp: 5,000 lux max.,
Sunlight: 10,000 lux max.
–10 to +55 °C (14 to 131°F), No freezing
35 to 85%, No condensation
10 to 55 Hz, 1.5 mm double amplitude in X, Y, and Z
directions, 2 hours respectively
500 m/s 2 in X, Y, and Z directions, 3 times respectively
Polycarbonate
Approx. 115 g
1. When several units are connected, the acceptable ambient temperature varies
depending on the conditions given below. To connect several units, be sure to
mount them to a DIN rail (metallic plate). Ensure that the output current is 20
mA max.
• When 3 to 10 units are connected: -10 to +50
°C (14 to 122°F)
• When 11 to 16 units are connected: -10 to +45 °C (14 to 113°F)
Amplifier Fiber unit
Detection method
Model
Type
Detection range
Smallest spot diameter
Minimum bend radius
Enclosure rating
Ambient temperature
Relative humidity
Fiber length
Housing material
Weight
CZ-40
Long detecting distance
70 ±20 mm
6 mm dia.
R25 mm
Reflective
IP67
–40 to +70 °C (–40 to 158°F), No freezing
35 to 85%, No condensation
2 m (free-cut)
Polyarylate
Approx. 27 g
CZ-41
Small beam spot
16 ±4 mm
1 mm dia.
R15 mm
Type
Model
Detection range
Smallest spot diameter
Minimum bend radius
Enclosure rating
Ambient temperature
Relative humidity
Fiber length
Housing material
Weight
Adjustable small beam spot
CZ-10
10 to 30 mm
0.9 to 3.5 mm dia.
Reflective
R25 mm
IP40
–40 to +70 °C (–40 to 158°F), No freezing
35 to 85%, No condensation
Lens housing: Aluminum, Fiber case: Stainless steel
Adjustable small beam spot, sideview
CZ-11
3 to 15 mm
0.9 to 1.5 mm dia.
2 m (free-cut) 1 m (free-cut)
Approx. 5 g Approx. 13 g
Instruction manual (This manual): 1
Mounting bracket: 1 Plastic screw driver: 1
96M0744