Check settings before you start, Select the signals to be monitored, O o o o – KORG Soundlink DRS REcording Console 168RC User Manual
Page 25: Maa biaa bha nffl, Biaa, Post post pre, Post solo mute, F.00+fr-eset fgm chi- mstr, Grp.link
Attention! The text in this document has been recognized automatically. To view the original document, you can use the "Original mode".
Chapter 2. Tutorial
4.
Check settings before you start
So that sound will not be accidentally output frona channels or buses during operations, and to
avoid sudden noises, make the following settings on the 168RC.
O
Rotate the [MONITOR] knob and [PHONES] knob fully left.
Q Set the channel faders 1~12 and the master fader to the -infinity dB position.
In I/S/P mode, set the level of channels 13-16 to 0. Press the [I/S/P] key (the LED will light)
to access I/S/P mode. Press the [SEE] key for channels 13-16 so that a channel 13-16 appears
in the LCD display. Press the [ ^ ] key to move the line to the LEVEL values. Rotate knob [8]
to the left to set the value to 0. Press the 13-16 [SEL] key to change channels, and set each
channel to a level of 0.
Input
n
QJ
Auxl Aux2 E f f l E f f 2
O O O O
dh dh Q
Post Post Pre
O
Pan LEUL
O 0‘
CHT
I
0
Q
SI
Post solo MUTE
0
Press the [MUTE] key for channel faders 1-12 and the master fader (the LEDs will light) to
mute them. Mute channels 13-16 in I/S/P mode. Press the [
V
] key to move the line to
"mute" (or "MUTE"). Press knob [8] to select "MUTE" and mute the channel. Press the 13-16
[SEL] key to change channels, and successively mute each channel.
O Set all [TRIM] knobs A-H to the "MIN" position.
0
Make settings so that no signals are sent to the internal buses. Press the [Ex.BUS I/O] key (the
LED will light) to access Ex.BUS 1/O mode. Use the [ ^ ] or [ \/ ] key to access the Input Sel.
page, and use knobs [l]-[8] to turn all parameters "OFF."
|j,ML:iiaa
El¡OFF
Gl¡OFF
G5¡0FF
мR¡llaa
E2¡0FF
G2¡0FF
G6¡0FF
SL¡llI¡a
Al ¡OFT
GЗ¡0FT
G7¡0FT
SR¡|
A2¡0FF
G4¡0FF
G8¡0FF
5.
Select the signals to be monitored
Send the master L/R signal to the monitor.
O Select master L/R as the signal to be sent to the monitor. Press the [SND MASTER] key (the
LED will light) to access SND MASTER mode. Press the [
A.
] key or [ v ] key to select the
Monitor page, and press knob [1] to turn Mstr "ON."
F.00+Fr-eset FGM Chi-
Mstr
qg
[Il
! I
Auxl Aux2 E f f l E f f 2
Q
5)
5)
O
maa Biaa BHa nffl
Grp.Link
Biaa
GIO G2B G3Q G4Q) G5Q) GÉB G70 G80
OFF OFF OFF OFF OFF OFF OFF OFF
0
Set the [TAPE IN/MONITOR] switch to MONITOR.
0
Adjust the [MONITOR] knob and the [PHONES] knob to an appropriate position (approxi
mately 9 o'clock).
O Set the master fader to the 24 dB position.
18