Golden Lighting 1323-M1L WG - Manual

Assembly Instructions: 1323-M1L WG (Ella)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important
notes above. Shut off the power at the circuit breaker and
completely remove the old fixture from the ceiling, including the
old mounting strap.
From the parts bag remove the mounting strap assembly. One
end of nipple (F) should be attached to mounting strap (A) with
hex nuts (C, D) in place. The other end should have canopy loop
(H) attached.
Attach mounting strap (A) to the junction box using mounting
screws (B) and a screwdriver. Tighten securely. Unscrew canopy
loop collar (I) from canopy loop (H). Pass canopy (G) over the
mounted canopy loop to test the height. Approximately half
of the canopy loop’s exterior threads should be exposed, and
the canopy loop collar should fit snugly onto the canopy loop.
Remove canopy (G) and adjust the height of nipple (F) and
canopy loop (H) until the desired height is reached.
ASSEMBLING THE FIXTURE
Use decorative nuts (M) to attach the arms to the fixture body.
Refer to the crystal installation sheet to hang the crystals.
HANGING THE FIXTURE
By measuring, determine the correct number of chain links
needed for proper hanging height. If necessary, use a pair
of pliers to open and remove any excess chain. Attach one
chain connector (K) to each end of chain (J). Use one of chain
connectors (K) to attach chain (J) to top loop (L) and close the
chain connector. Feed the fixture wires up through the chain
(every three links or so), pulling the wires until taut. Slide canopy
loop collar (H) and canopy (G) onto the chain/wire. Use the free
chain connector (K) to attach chain (J) to canopy loop (H).
CONNECTING THE WIRES
Have an assistant support the fixture weight while completing
the wiring. Cut away excess wire. Thread the fixture wires
through canopy loop (H) and nipple (F). Attach the fixture’s wires
to the power supply wires from the junction box. Connect black
to black (or smooth); white to white (or ribbed); ground to ground
(green or copper). Twist the ends of the wire pairs together, then
twist on a wire connector. Make sure all twists are in the same
direction. If there is no ground wire (green or copper) from the
junction box, locate ground screw (E) on mounting strap (A) and
wrap the fixture ground wire around the green ground screw (E).
Use a screwdriver to secure ground screw (E) onto the mounting
bracket. Tuck all wires neatly into the junction box.
FINISHING THE INSTALLATION
Push canopy (G) up to the ceiling and slide canopy loop collar (I)
up beneath the canopy. Tightly thread canopy loop collar (I) onto
canopy loop (H) to secure canopy (G) in place.
Install bulb (O) in accordance with the fixture’s specifications.
See the bulb note below. Gently screw bulbshield (P) around the
socket. Do not overtighten.
Bulb Note: Use a tissue or paper towel to hold the bulb and
push down into the socket. Oils and dirt can cause the bulb life
to shorten. Rubbing alcohol is recommended for cleaning.
Your installation is now complete. Turn on the power and test
the fixture.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.
For Customer Service, contact
the place of purchase to arrange
for replacement parts.
BLACK
(Hot)
WHITE
(Neutral)
GREEN
(Ground)
HOUSE WIRES
SMOOTH
(Or Black)
FIXTURE WIRES
RIBBED
(Or White)
BARE COPPER
(Or Green)
A
E
B
D C
G
I
K
P
L
M
O
N
J
H
F