Golden Lighting 1401-S RBZ - Manual

Assembly Instructions: 1401-S/M (Handley)
IMPORTANT:
• All InstAllAtIon work sHould be done by AccredIted professIonAl.
• sHut off power supply At fuse or cIrcuIt breAker!
• use only tHe specIfIed bulbs. do not exceed tHe mAxImum wAttAge!
PRePARINg fOR INSTAllATION
remove all of the contents from the carton. see the important
notes above. shut off the power at the circuit breaker and
completely remove the old fixture from the ceiling, including
the old mounting strap.
From the parts bag remove the mounting strap assembly.
One end of nipple (F) should be attached to mounting strap
(A) with hex nuts (C, D) in place. The other end should have
canopy loop (H) attached.
Mounting strap (A) contains several pairs of threaded holes.
Find the pair of holes that matches the spacing of the holes
on the junction box. Attach mounting strap (A) to the junction
box using mounting screws (B) and a screwdriver. Tighten
securely. unscrew canopy loop collar (I) from canopy loop
(H). pass canopy (g) over the mounted canopy loop to test
the height. Approximately half of the canopy loop’s exterior
threads should be exposed, and the canopy loop collar
should fit snugly onto the canopy loop. Remove canopy (G)
and adjust the height of nipple (F) and canopy loop (H) until
the desired height is reached.
ASSeMblINg The fIxTuRe
Attach top loop (L) to fixture body (N). By measuring,
determine the correct length of chain needed for proper
hanging height. If necessary, use a pair of pliers to open and
remove any excess chain. Attach one of chain connectors
(K) to each end of chain (J). Pass the fixture wires through
top loop (l). pull the wires until taut. Attach one end of chain
connector (k) to top loop (l) and close chain connector (k).
Feed the fixture wires up through the chain (every three links
or so), pulling the wires until taut. Carefully slide glass shade
(O) over top loop (L) and fixture body (N). Use the free chain
connector (k) to attach chain (J) to canopy loop (H). slide
canopy loop collar (H) and canopy (g) down onto the chain/
wire. pull the wires until taut. trim the wires to the desired
length plus 8 to 10 inches.
CONNeCTINg The WIReS
Have an assistant support the fixture weight while completing
the wiring. Thread the fixture wires through canopy loop
(H) and nipple (F). Attach the fixture’s wires to the power
supply wires from the junction box. Connect black to black
(or smooth); white to white (or ribbed); ground to ground
(green or copper). Twist the ends of the wire pairs together,
then twist on a wire connector. make sure all twists are in the
same direction. If there is no ground wire (green or copper)
from the junction box, locate ground screw (E) on mounting
strap (A) and wrap the fixture ground wire around the green
ground screw (E). Use a screwdriver to secure ground screw
(E) onto the mounting bracket. Tuck all wires neatly into the
junction box.
fINIShINg The INSTAllATION
Push canopy (G) up to the ceiling and slide canopy loop
collar (I) up beneath the canopy. Tightly thread canopy loop
collar (I) onto canopy loop (H) to secure canopy (g) in place.
Install bulb (M) (not included) in accordance with the fixture’s
specifications. Do not exceed the maximum wattage.
your installation is now complete. turn on the power and test
the fixture.
CleANINg TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture. For deep cleaning, turn off the light
and remove the glass prior to cleaning. Hand wash glass with warm water and mild detergent. Dry with a lint-free or microfiber cloth.
for Customer Service, contact
the place of purchase to arrange
for replacement parts.
BLACK
(Hot)
WHITE
(Neutral)
GREEN
(Ground)
HOUSE WIRES
SMOOTH
(Or Black)
FIXTURE WIRES
RIBBED
(Or White)
BARE COPPER
(Or Green)
A
B
C
H
I
G
J
K
E
D
F
L
N
P
M
O