Golden Lighting 1821-6P/9P BI - Manual

Assembly Instructions: 1821-6P/9P (Madera)
IMPORTANT:
• All InstAllAtIon work should be done by AccredIted professIonAl.
• shut off power supply At fuse or cIrcuIt breAker!
• use only the specIfIed bulbs. do not exceed the MAxIMuM wAttAge!
PRePARINg fOR INsTAllATION
remove all of the contents from the carton. see the important
notes above. shut off the power at the circuit breaker and
completely remove the old fixture from the ceiling, including the
old mounting strap.
From the parts bag remove the mounting strap assembly. One
end of nipple (F) should be attached to mounting strap (A) with
hex nuts (C, D) in place. The other end should have canopy
loop (H) attached. Attach mounting strap (A) to the junction box
using mounting screws (B) and a screwdriver. Tighten securely.
unscrew canopy loop collar (I) from canopy loop (h). pass
canopy (G) over the mounted canopy loop to test the height.
Approximately half of the canopy loop’s exterior threads should
be exposed, and the canopy loop collar should fit snugly onto
the canopy loop. Remove canopy (G) and adjust the height
of nipple (F) and canopy loop (H) until the desired height is
reached.
AsseMblINg The fIxTuRe
Rods (Q) are on the fixture wires. Pull the fixture wires through
one of rod (Q). Pull the wires taut before threading the rod to
center nipple (r). slide candle sleeves (p) over the sockets.
Install bulbs (O) (not provided) in accordance with the fixture’s
specifications. Do not exceed the maximum wattage. Slide
the remaining rod (Q) down over the wires and pull taut before
connecting the threads to the exposed threads of the rod that
is attached to the fixture body. Thread the free end of the rod to
the top loop. Attach one end of each decorative chains (n) to
hooks (M) on the cage and on the top cap.
By measuring, determine the correct number of chain links
needed for proper hanging height. If necessary, use a pair of
pliers to open and remove any excess chain (J). Attach one
chain connector (K) to each end of chain (J). Twist to secure in
place. Use one of chain connectors (K) to attach chain (J) to top
loop (L) and close the chain connector. Feed the fixture wires
up through the chain (every three links or so), pulling the wires
until taut. slide canopy loop collar (h) and canopy (g) onto the
chain/wire. Use the free chain connector (K) to attach chain (J) to
canopy loop (h).
CONNeCTINg The WIRes
Have an assistant support the fixture weight while completing
the wiring. Cut away excess wire. Thread the fixture wires
through canopy loop (H) and nipple (F). Attach the fixture’s wires
to the power supply wires from the junction box. Connect black
to black (or smooth); white to white (or ribbed); ground to ground
(green or copper). Twist the ends of the wire pairs together, then
twist on a wire connector. Make sure all twists are in the same
direction. If there is no ground wire (green or copper) from the
junction box, locate ground screw (E) on mounting strap (A) and
wrap the fixture ground wire around the green ground screw (E).
Use a screwdriver to secure ground screw (E) onto the mounting
bracket. Tuck all wires neatly into the junction box.
fINIshINg The INsTAllATION
Push canopy (G) up to the ceiling and slide canopy loop collar (I)
up beneath the canopy. Tightly thread canopy loop collar (I) onto
canopy loop (h) to secure canopy (g) in place.
your installation is now complete. turn on the power and test
the fixture.
CleANINg TIPs
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture.
for Customer service, contact
the place of purchase to arrange
for replacement parts.
BLACK
(Hot)
WHITE
(Neutral)
GREEN
(Ground)
HOUSE WIRES
SMOOTH
(Or Black)
FIXTURE WIRES
RIBBED
(Or White)
BARE COPPER
(Or Green)
A
E
B
H
K
G
I
C,D
F
J
N
Q
O
R
L
M
P