Golden Lighting 8107-BA1 WG - Manual

Assembly Instructions: 8107-9 WG (Torbellino)
IMPORTANT:
• ALL INSTALLATION WORK SHOULD BE DONE BY ACCREDITED PROFESSIONAL.
• SHUT OFF POWER SUPPLY AT FUSE OR CIRCUIT BREAKER!
• USE ONLY THE SPECIFIED BULBS. DO NOT EXCEED THE MAXIMUM WATTAGE!
PREPARING FOR INSTALLATION
Remove all of the contents from the carton. See the important
notes above. Shut off the power at the circuit breaker and
completely remove the old fixture from the ceiling, including
the old mounting strap.
From the parts bag remove the mounting strap assembly.
One end of nipple (F) should be attached to mounting strap
(A) with hex nuts (C, D) in place. The other end should have
canopy loop (H) attached.
Mounting strap (A) contains several pairs of threaded holes.
Find the pair of holes that matches the spacing of the holes
on the junction box. Attach mounting strap (A) to the junction
box using mounting screws (B) and a screwdriver. Tighten
securely. Unscrew canopy loop collar (I) from canopy loop
(H). Pass canopy (G) over the mounted canopy loop to test
the height. Approximately half of the canopy loop’s exterior
threads should be exposed, and the canopy loop collar
should fit snugly onto the canopy loop. Remove canopy (G)
and adjust the height of nipple (F) and canopy loop (H) until
the desired height is reached.
ASSEMBLING THE FIXTURE
If the arms of the fixture are packed closed, gently spread
the arms until they are evenly spaced. Use decorative thumb
screw (R) to secure the arms to housing (Q). Place the bottom
of the fixture on a flat surface. Top loop (L) is on the fixture
wires, but not attached to the body of the fixture. Pass the
fixture wires through top loop (L). Pull the wires until taut and
thread top loop (L) onto the fixture body.
By measuring, determine the correct number of chain links
needed for proper hanging height. If necessary, use a pair
of pliers to open and remove any excess chain. Attach one
chain connector (K) to each end of chain (J). Use one of chain
connectors (K) to attach chain (J) to top loop (L) and close the
chain connector. Feed the fixture wires up through the chain
(every three links or so), pulling the wires until taut. Slide
canopy loop collar (H) and canopy (G) onto the chain/wire.
Use the free chain connector (K) to attach chain (J) to canopy
loop (H).
CONNECTING THE WIRES
Have an assistant support the fixture weight while completing
the wiring. Cut away excess wire. Thread the fixture wires
through canopy loop (H) and nipple (F). Attach the fixture’s
wires to the power supply wires from the junction box.
Connect black to black (or smooth); white to white (or ribbed);
ground to ground (green or copper). Twist the ends of the
wire pairs together, then twist on a wire connector. Make
sure all twists are in the same direction. If there is no ground
wire (green or copper) from the junction box, locate ground
screw (E) on mounting strap (A) and wrap the fixture ground
wire around the green ground screw (E). Use a screwdriver to
secure ground screw (E) onto the mounting bracket. Tuck all
wires neatly into the junction box.
FINISHING THE INSTALLATION
Push canopy (G) up to the ceiling and slide canopy loop
collar (I) up beneath the canopy. Tightly thread canopy loop
collar (I) onto canopy loop (H) to secure canopy (G) in place.
Slide glass shades (O) onto sockets (P) and secure the glass
in place with socket rings (N). Install bulbs (M) (not included)
in accordance with the fixture’s specifications. Do not exceed
the maximum wattage.
Your installation is now complete. Turn on the power and test
the fixture.
CLEANING TIPS
Treat the fixture gently! Regular cleaning will reduce the need for deep cleaning. For regular cleaning, turn off the light and wipe down the
fixture with a clean lint-free cotton or microfiber cloth. Never spray cleaner directly onto the fixture. For deep cleaning, turn off the light
and remove the glass prior to cleaning. Hand wash glass with warm water and mild detergent. Dry with a lint-free or microfiber cloth.
M
N
O
P
R
Q
A
B
C
H
I
G
J
K
E
D
F
L
BLACK
(Hot)
WHITE
(Neutral)
GREEN
(Ground)
HOUSE WIRES
SMOOTH
(Or Black)
FIXTURE WIRES
RIBBED
(Or White)
BARE COPPER
(Or Green)
For Customer Service, contact
the place of purchase to arrange
for replacement parts.