Zoom R16 - Manual (Page 87)

R16 eff
ect types and parameter
s
86
R16 effect types and parameters 8
Table 2
Setting value Description
Off Frequency does not change.
Up Frequency changes from minimum to maximum according to the controlling waveform.
Down Frequency changes from maximum to minimum according to the controlling waveform.
Hi Frequency changes from patch setting to maximum according to the controlling waveform.
Lo Frequency changes from minimum to patch setting according to the controlling waveform.
Table 3
Setting
value
Description
Setting
value
Description
Up Saw Rising sawtooth wave Tri Triangular wave
Up Fin Rising fin wave TrixTri Squared triangular wave
DownSaw Falling sawtooth wave Sine Sine wave
DownFin Falling fin wave Square Square wave
Table 4
Setting
value
Description
Setting
value
Description
Eighth note 1 bar 1 measure
Quarter note 2 bars 2 measures
Half note 3 bars 3 measures
Dotted half note 4 bars 4 measures
• The note range actually available depends on the parameter.
• Depending on the combination of tempo setting and selected note symbol, the parameter setting range could be exceeded. In such a
case, the value is automatically halved (or set to 1/4 if the range is still exceeded).
NOTE
Table 1
Parameters marked with allow selection of a setting value in note units, using the song/pattern tempo as reference.
The note durations for the setting values are shown below.
Thirty-second note Dotted sixteenth note Dotted eighth note Quarter note x 2
Sixteenth note Eighth note Quarter note : :
Quarter triplet note Half triplet note Dotted quarter note Quarter note x 20
Table 5
Setting
value
Description
1 1 semitone lower — original sound
2 Original sound — 1 semitone lower
3 Doubling — detune + original sound
4 Detune + original sound — doubling
5 Original sound — 1 octave higher
6 1 octave higher — original sound
7 Original sound — 2 octaves lower
8 2 octaves lower — original sound
9 1 octave lower + original sound — 1 octave higher + original sound
Setting
value
Description
10 1 octave higher + original sound — 1 octave lower + original sound
11
Complete fifth down + original sound — complete
fourth up + original sound
12
Complete fourth up + original sound — complete fifth
down + original sound
13 0 Hz + original sound — 1 octave up
14 1 octave up — 0 Hz + original sound
15 0 Hz + original sound — 1 octave up + original sound
16 1 octave up + original sound — 0 Hz + original sound
Rate 0~50 (P.86 Table 1)
Adjusts modulation rate. Using the rhythm tempo as reference,
setting in note units is also possible.
Clip 0~10 Adds emphasis by clipping the modulation waveform.
Shift −12~12,24
For an explanation of types and parameters, see CLEAN, DISTOR-
TION, ACO/BASS SIM algorithms.
Time
Delay, Echo: 1~2000ms (P.86 Table 1)
Adjusts delay time.
Doubling: 1~100ms
Feedback 0~100 Adjusts feedback amount.
Mix 0~100 Adjusts mix ratio of effect sound to original sound.
Tone 0~10 Adjusts tonal quality.
Fine −25~25 Adjust pitch shift amount in cent (1/100 semitone) units.
Balance 0~100 Adjust balance between original sound and effect sound.
Rise1 0~30 Adjusts stereo component intensity.
Rise2 0~30 Adjusts mono component intensity.
Freq Offset 1~30 Adjusts LFO offset.
Filter Type HPF, LPF, BPF Selects filter type.
Resonance 1~30 Adjusts resonance intensity.
EFX Level 0~100 Adjusts effect sound level.
Dry Level 0~100 Adjusts original sound level.
Type Parameters/Description
ZNR For an explanation of types and parameters, see CLEAN, DISTORTION, ACO/BASS SIM algorithms.
ZNR module