Rtx220 qr - manual – CRU RTX Secure 610-IR User Manual
Page 26
RTX220 QR - Manual
Page 26
Level
Type
Description
Error
SATA enable device fail
Failed to enable the SATA PCI device
Error
SATA EDMA mem fail
Failed to allocate memory for SATA EDMA
Error
SATA remap mem fail
Failed to remap SATA memory IO space
Error
SATA PRD mem fail
Failed ot initialize SATA PRD memory
manager
Error
SATA revision ID fail
Failed to get SATA revision ID
Error
SATA reg fail
Failed to set SATA register
Error
SATA init fail
Core failed to initialize the SATA adapter
Error
SATA diag fail
SATA Adapter diagnostics failed
Error
Mode ID fail
SATA Mode ID failed
Error
SATA chip count error
SATA chip count error
Info
SAS port reply error
SAS HBA port <number> reply terminated
abnormally
Info
SAS unknown port reply
error
SAS frontend reply terminated abnormally
Info
FC port reply error
FC HBA port <number> reply terminated
abnormally
Info
FC unknown port reply
error
FC frontend reply terminated abnormally
EMS Events
Level
Type
Description
Info
Power install
Power(<string>) is installed
Error
Power absent
Power(<string>) is absent
Info
Power restore
Power(<string>) is restored to work
Error
Power fail
Power(<string>) is not functioning
Warning
Power detect
PSU signal detection(<string>)
Info
Fan restore
Fan(<string>) is restored to work
Error
Fan fail
Fan(<string>) is not functioning
Info
Fan install
Fan(<string>) is installed
Error
Fan not present
Fan(<string>) is not present
Error
Fan over speed
Fan(<string>) is over speed
Warning
Thermal level 1
System temperature(<string>) is higher
Error
Thermal level 2
System overheated(<string>)!!!
Error
Thermal level 2 shutdown
System overheated(<string>)!!! The sys-
tem will auto-shutdown immediately.
Error
Thermal level 2 CTR
shutdown
The controller will auto shutdown immedi-
ately, reason [ Overheated(<string>) ].
Warning
Thermal ignore value
Unable to update thermal value on
<string>
Warning
Voltage level 1
System voltage(<string>) is higher/lower.
Level
Type
Description
Error
Voltage level 2
System voltages(<string>) failed!!!
Error
Voltage level 2 shutdown
System voltages(<string>) failed!!! The
system will autho shutdown immediately.
Error
Voltage level 2 CTR
shutdown
The controller will auto shutdown immedi-
ately, reason [ Voltage abnormal(<string>)
].
Info
UPS OK
Successfully detect UPS
Warning
UPS fail
Failed to detect UPS
Error
UPS AC loss
AC loss for system detected
Error
UPS power low
UPS Power Low!!! The system will auto-
shutdown immediately.
Warning
SMART T.E.C.
Disk <slot> S.M.A.R.T. Threshold Exceed
Condition occurred for attribute <string>
Warning
SMART fail
Disk <slot>: Failure to get S.M.A.R.T.
information
Warning
RedBoot failover
RedBoot failover event occurred
Warning
Watchdog shutdown
Watchdog timeout shutdown occurred
Warning
Watchdog reset
Watchdog timeout reset occurred
Info
Console Login
<username> login from <IP or serial
console> via Console UI
Info
Console Logout
<username> logout from <IP or serial
console> via Console UI
Info
Web Login
<username> login from <IP> via Web UI
Info
Web Logout
<username logout from <IP> via Web UI
Info
Log clear
All event logs are cleared
Warning
Send mail fail
Failed to send event to <email>
LVM Events
Level
Type
Description
Info
RG create OK
RG <name> has been created
Info
RG create fail
Failed to create RG <name>
Info
RG delete
RG <name> has been deleted
Info
RG rename
RG <name> has been renamed as <name>
Info
VD create OK
VD <name> has been created.
Info
VD create fail
Failed to create VD <name>
Info
VD delete
VD <name> has been deleted
Info
VD rename
The name of VD <name> has been
renamed to <name>
Info
VD read only
Cache policy of VD <name> has been set
as read only
Info
VD write back
Cache policy of VD <name> has been set
as write-back