Beisler 100-58 - Manual (Page 52)

3-2
2.10.6 Change light mask ............................................................................................... 3-16
2.11 Dart stretcher ....................................................................................................... 3-16
2.11.1 Fixing in the guiding plate .................................................................................... 3-16
2.11.2 Magnet switch at the dart stretcher cylinder ........................................................ 3-16
3 Adjustments at the sewing head ...................................................................... 3-17
3.1 Height adjustment ................................................................................................ 3-17
3.2 Lateral adjustment ............................................................................................... 3-17
3.3 Driving belt tension of the sewing motor .............................................................. 3-17
3.4 Top threat cutter (Beisler sewing head) ............................................................... 3-18
3.5 Height of top threat catcher ................................................................................. 3-18
3.6 Center knife adjustments ..................................................................................... 3-18
3.6.1 Switching on ........................................................................................................ 3-18
3.6.2 Switching off ........................................................................................................ 3-18
3.6.3 Safety initiator at the center knife pole ................................................................. 3-18
3.6.4 Depth adjustment of the safety initiator ............................................................... 3-18
3.6.5 Height of center knife ........................................................................................... 3-19
3.6.6 Shear angle of the center knife ............................................................................ 3-19
3.6.7 Lateral adjustment ............................................................................................... 3-19
3.6.8 Needle protection ................................................................................................. 3-19
3.7 Adjustments of the bobbin threat catcher (Beisler sewing head) ......................... 3-20
3.7.1 Catcher adjustment .............................................................................................. 3-20
3.7.2 Time of bobbin threat cutting ............................................................................... 3-20
3.7.3 Duration of bobbin threat cutting .......................................................................... 3-20
3.8 Sensitivity of the bobbin detector (option) ............................................................ 3-20
3.9 Clean tactual head of the bobbin detector (option) .............................................. 3-21
3.10 Adjust piping detection ......................................................................................... 3-21
3.10.1 Lateral adjustment ............................................................................................... 3-21
3.10.2 Adjust intensity ..................................................................................................... 3-21
3.11 Swing up sewing head ......................................................................................... 3-22
3.12 Upper threat monitor ............................................................................................ 3-22
3.12.1 Switch on time ..................................................................................................... 3-22
3.12.2 Filter threat monitor .............................................................................................. 3-22
4 Adjustments at the mitre knifes ....................................................................... 3-23
4.1 Basic adjustment locked mitre knife (seam end) ................................................. 3-23
4.2 Basic adjustment movable mitre knife (seam start) ............................................. 3-23
4.3 Mitre knife height ................................................................................................. 3-23
4.4 Mitre knife broadth ............................................................................................... 3-23
4.5 Pre-stabber .......................................................................................................... 3-24
4.6 Lateral adjustment ............................................................................................... 3-24
4.7 Fine adjustment in the length ............................................................................... 3-24
4.8 Tighten cog-belt of the mitre knife drive ............................................................... 3-24
5 Adjustment of machine options ....................................................................... 3-25
5.1 Automatic push-back blocking ............................................................................. 3-25
5.2 Height of the take off roller ................................................................................... 3-25
5.3 Mitre knife slant position ...................................................................................... 3-26
5.3.1 Distance between basic bodies ........................................................................... 3-26
5.3.2 Height adjustment ................................................................................................ 3-26
5.3.3 Center adjustment ............................................................................................... 3-26
5.3.4 Adjust mitre knife stops ........................................................................................ 3-26
5.3.5 Knife arrangement ............................................................................................... 3-26
5.3.6 Arrangement of the mitre knife during flap pocket production ............................. 3-27
5.4 Split needle (Beisler sewing head) ....................................................................... 3-27
5.4.1 Distance to cylinder of the top threat catcher ...................................................... 3-27
5.4.2 Center adjustment ............................................................................................... 3-27
5.5 Vylene adjustments .............................................................................................. 3-27
5.5.1 Correct vylene adjustment ................................................................................... 3-27
5.5.2 Demount vylene plate .......................................................................................... 3-28
5.5.3 Change cutting pressure ...................................................................................... 3-28
5.5.4 Adjust vylene supply ............................................................................................ 3-28
5.5.5 Easy-running of the vylene roll ............................................................................ 3-28
5.5.6 Vylene supply speed ............................................................................................ 3-28