Document Outline

• Start Here
  • System Requirements
  • Package Contents
  • Install ProSoft Configuration Builder Software
• To install ProSoft Configuration Builder from the ProSoft Web Site
• To install ProSoft Configuration Builder from the Product CD
  • Setting Jumpers
  • Install the Module in the Rack
  • Connect your PC to the Processor
  • Download the Sample Program to the Processor
• To download the sample program from RSLogix 5 to the PLC processor:
  • Configuring the RSLinx Driver for the PC COM Port
• If RSLogix is unable to establish communication with the processor, follow these steps
  • Connect your PC to the Module
• Module Configuration
  • Installing and Configuring the Module
    • Example of 240 words of read and write data (cfg file=10)
    • Example of 2300 read and 3500 write data registers (cfg file=10)
  • Module Data
  • Status Data
  • User Data
  • Event Command Data
  • Modbus Message Data
  • ProSoft Configuration Builder
    • Set Up the Project
    • Set Module Parameters
• To rename an object:
  • Module Entries
• To configure module parameters
  • Printing a Configuration File
• To print a configuration file:
  • [Module]
    • Module Name
      • Error/Status Pointer
      • Read Register Start
      • Read Register Count
      • Write Register Start
      • Write Register Count
      • Failure Flag Count
      • Initialize Output Data
      • Pass-Through Mode
      • Duplex/Speed Code
    • [Static ARP Table]
      • IP Address
      • Hardware MAC Address
    • [MNET Client x]
      • Error/Status Pointer
      • Minimum Command Delay
      • Command Error Pointer
      • Response Timeout
      • Retry Count
      • Float Flag
      • Float Start
      • Float Offset
      • ARP Timeout
      • Command Error Delay
    • [MNET Client x Commands]
      • Command List Overview
      • Commands Supported by the Module
      • Command Entry Formats
        • MNET MODBUS Command Structure
      • Enable
      • Internal Address
      • Poll Interval
      • Reg Count
      • Swap Code
      • Node IP Address
      • Service Port
      • Slave Address
      • Modbus Function
      • MB Address in Device
      • Comment
    • [MNET Servers]
      • Float Flag
      • Float Start
      • Float Offset
      • Output Offset
      • Bit Input Offset
      • Holding Register Offset
      • Word Input Offset
    • Ethernet Configuration
  • Download the Project to the Module
• To Download the Project File
• Ladder Logic
• Diagnostics and Troubleshooting
  • Reading Status Data from the Module
    • Required Hardware
    • The Configuration/Debug Menu
      • Using the Diagnostic Window in ProSoft Configuration Builder
      • Navigation
      • Keystrokes
    • Main Menu
      • Viewing Block Transfer Statistics
      • Viewing Module Configuration
      • Opening the Database Menu
      • Opening the Command List Menu
      • Opening the Command Error List Menu
      • Receiving the Configuration File
      • Sending the Configuration File
      • Resetting diagnostic data
      • Viewing Version Information
      • Warm Booting the Module
      • Viewing Network Status
      • Viewing Client Status
      • Viewing Client Configuration
      • Viewing Server Configuration
      • Exiting the Program
    • Modbus Database View
      • Viewing Register Pages
      • Redisplaying the Current Page
      • Moving Back Through 5 Pages of Registers
      • Viewing the Previous 100 Registers of Data
      • Moving Forward Through 5 Pages of Registers
      • Viewing the Next 100 Registers of Data
      • Viewing Data in Decimal Format
      • Viewing Data in Hexadecimal Format
      • Viewing Data in Floating Point Format
      • Viewing Data in ASCII (Text) Format
      • Returning to the Main Menu
    • Command List Menu
      • Redisplaying the Menu
      • Redisplaying the Current Page
      • Viewing the Previous Page of Commands
      • Viewing the Next Page of Commands
      • Returning to the Main Menu
    • Network Menu
      • Transferring WATTCP.CFG to the module
      • Transferring WATTCP.CFG to the PC
      • Viewing the WATTCP.CFG file on the module
      • Returning to the Main Menu
  • LED Status Indicators
    • Ethernet LED Indicators
    • Clearing a Fault Condition
    • Troubleshooting
• Reference
  • Product Specifications
    • General Specifications
    • Hardware Specifications
    • Functional Specifications
  • Functional Overview
    • General Concepts
      • Module Power Up
      • Main Logic Loop
      • Block Transfer Backplane Data Transfer
        • Normal Data Transfer
          • Read Block
          • Write Block
        • Initialize Output Data
        • Command Control Blocks
          • Event Command
          • Command Control
          • Warm Boot
          • Cold Boot
        • Pass-Through Control Blocks
      • Side-Connect Backplane Data Transfer
        • Example of 240 words of read and write data (cfg file=10)
        • Example of 2300 read and 3500 write data registers (cfg file=10)
        • Command Control Blocks
          • Event Command
          • Command Control
          • Warm Boot
          • Cold Boot
        • Pass-Through Control Blocks
    • Data Flow between MVI71-MNET Module and PLC Processor
      • Server Driver
      • Client Driver
        • Client Command List
  • Cable Connections
    • Ethernet Connection
      • Ethernet Port Configuration - wattcp.cfg
    • RS-232 Configuration/Debug Port
      • Disabling the RSLinx Driver for the Com Port on the PC
    • DB9 to RJ45 Adaptor (Cable 14)
  • MVI71-MNET Status Data Definition for Side Connect File
  • Status Data Structure for Database Storage
  • Client Error/Status Data
    • MNET Server Port 2000 Status Error Locations
    • MNET Server Port 502 Status Error Locations
    • MNET Server Port 2001 Error Locations
    • MNET Client Command List Error Data
      • Standard Modbus Protocol Errors
      • Module Communication Error Codes
      • MNET Client Specific Errors
      • Command List Entry Errors
  • Modbus Protocol Specification
    • Read Coil Status (Function Code 01)
    • Read Input Status (Function Code 02)
    • Read Holding Registers (Function Code 03)
    • Read Input Registers (Function Code 04)
    • Force Single Coil (Function Code 05)
    • Preset Single Register (Function Code 06)
    • Diagnostics (Function Code 08)
      • Sub-function codes supported by the serial line devices
        • 00 Return Query Data
        • Example and state diagram
    • Force Multiple Coils (Function Code 15)
    • Preset Multiple Registers (Function Code 16)
    • MODBUS Exception Responses
      • MODBUS Exception Codes
• Support, Service & Warranty
  • How to Contact Us: Technical Support
  • Return Material Authorization (RMA) Policies and Conditions
    • All Product Returns:
    • Procedures for Return of Units Under Warranty:
    • Procedures for Return of Units Out of Warranty:
    • Purchasing Warranty Extension:
  • LIMITED WARRANTY
    • What Is Covered By This Warranty
    • What Is Not Covered By This Warranty
    • Disclaimer Regarding High Risk Activities
    • Intellectual Property Indemnity
    • Disclaimer of all Other Warranties
    • Limitation of Remedies **
    • Time Limit for Bringing Suit
    • No Other Warranties
    • Allocation of Risks
    • Controlling Law and Severability
• Index