Roland P-20HD Video Instant Replayer - Manual (Page 58)

58
Menu List
8: Audio Input
Menu item Value
(Bold: default)
Explanation
LIVE IN 1 [ENTER] Configures the audio input for LIVE IN 1.
LIVE IN 2 [ENTER] Configures the audio input for LIVE IN 2.
AUDIO IN [ENTER] Configures the audio input for AUDIO IN.
LIVE IN Bus [ENTER] Configures the audio input for the LIVE IN bus.
REPLAY [ENTER] Configures the audio input for REPLAY.
AUDIO PLAYER [ENTER] Configures the audio player settings.
LIVE IN 1, LIVE IN 2, AUDIO IN
Menu item Value
(Bold: default)
Explanation
Level -INF, -80.0– 0.0 – +10.0dB Adjusts the input volume.
Mute Off , On Turns the mute function on/off. If this is set to “On,” the input audio is temporarily muted.
Delay 0.0 –95.0ms ( 0.0 –5.6/4.7Frame)
Adjusts the delay time of the audio.
* The range for the frame rate setting differs depending on the Frame Rate setting (59.97Hz/50Hz).
Effect Delays the output of the effect audio.
HPF 75Hz Off , On
Turns the high-pass filter on/off.
Effect Cuts off low-band audio not required for the effect. The cutoff frequency is 75 Hz.
Send to
(only for AUDIO IN)
LIVE IN Bus , Input Bus
Sets whether to mix the AUDIO IN audio with the LIVE IN bus, or whether to mix it with
the Input bus.
Gate Off , On
Turns the noise gate on/off.
Effect Eliminates audio that is lower than the specified threshold level.
Threshold -80.0– -50 –0.0dB
Specifies the base level used as the threshold for removing audio. Audio below the
level set here is removed.
Release 30– 860 –5000ms
Adjusts the length of time until the audio is fully attenuated after the audio level falls
below the threshold.
Compressor Off , On
Turns the compressor on/off.
Effect Audio that exceeds the specified effect threshold level is compressed.
Threshold -50– -8 –0dB
Specifies the base level at which the compressor is applied. Compression is applied to
audio that exceeds the threshold.
Ratio
1.00:1, 1.12:1, 1.25:1, 1.40:1, 1.60:1,
1.80:1, 2.00:1, 2.50:1 , 3.20:1, 4.00:1,
5.60:1, 8.00:1, 16.0:1, INF:1
Specifies the degree of compression applied to the audio. The state in which no
compression is applied is defined as “1.”
Attack 0– 3.0 –100ms Specifies the time until compression starts when audio exceeding the threshold is input.
Release 30– 250 –5000ms Adjusts the length of time until compression ends after audio falls below the threshold.
Makeup Gain -40– 0 –40dB Adjusts the final output volume level after applying the compressor.
EQ Off , On
Turns the equalizer on/off.
Effect Adjusts the volume for each frequency band.
Hi Gain -15.0– 0.0 –15.0dB Boosts or attenuates the high band.
Hi Freq 1.0kHz– 10.0kHz –20.0kHz Adjusts the center frequency when changing the volume in the high band.
Mid Gain -15.0– 0.0 –15.0dB Boosts or attenuates the midrange band.
Mid Freq 20Hz– 500Hz –20.0kHz Adjusts the center frequency when changing the volume in the midrange band.
Mid Q 0.5– 1.0 –16.0 Adjusts the frequency bandwidth when boosting or attenuating the midrange band.
Lo Gain -15.0– 0.0 –15.0dB Boosts or attenuates the low band.
Lo Freq 20Hz– 100Hz –2.0kHz Adjusts the center frequency when changing the volume in the low band.