Hitachi SJ300 Series - Manual (Page 26)

26
Chapter 3 – Parameter Setting Tables
Function Mode
Code Function name Setting range Initial data remarks
A092 Acceleration time2 0.01-99.99/100.0-999.9/1000.-3600.(s) 15.00
A093 Deceleration time2 0.01-99.99/100.0-999.9/1000.-3600.(s) 15.00
A094 2 nd stage adjustable selection 00(change with 2CH terminal)/01(change with setting) 00
*A095 2 nd acceleration frequency 0.00-99.99/100.0-400.0(Hz) 0.00
*A096 2 nd deceleration frequency 0.00-99.99/100.0-400.0(Hz) 0.00
A097 Acceleration pattern selection
00(straight line)/01(S-curve)/02(U-curve)/03(reverse U-curve)/
04(EL-S curve)
04
A098 Deceleration pattern selection
00(straight line)/01(S-curve)/02(U-curve)/03(reverse U-curve)/
04(EL-S curve)
04
*A101 OI start frequency 0.00-99.99/100.0-400.0(Hz) 0.00
*A102 OI end frequency 0.00-99.99/100.0-400.0(Hz) 0.00
A103 OI start current 0.-100. (%) 20.
A104 OI end current 0.-100. (%) 100.
A105 OI start selection 00(external start frequency)/01(0Hz) 01
*A111 O2 start frequency 0.00-99.99/100.0-400.0(Hz) 0.00
*A112 O2 end frequency 0.00-99.99/100.0-400.0(Hz) 0.00
A113 O2 start voltage 0.-100. (%) -100%
A114 O2 end voltage 0.-100. (%) 100%
A131 Acceleration curve constant 01(small swelling)-10(large swelling) 01
A132 Deceleration curve constant 01(small swelling-10(large swelling) 01
b001 Retry selection
00(trip)/01(0Hz start)/02(start after equal frequency)/
03(trip after equaling frequency and deceleration stop)
00
b002
Allowable under-voltage power
failure time
0.3-1.0(s) 0.3
b003 Retry wait time 0.3-100.(s) 1.0
b004
Instantaneous power failure/
under-voltage trip during stop 00(invalid/01(valid)/02(invalid during stop and deceleration by stop
command)
01
b005
Instantaneous power failure/
under-voltage retry time
selection
00(16 times)/01(free) 00
b006 Open-phase selection 00(invalid)/01(valid) 00
*b007 Frequency setting to match 0.00-99.99/100.0-400.0(Hz) 0.00
b012 Electronic thermal level 0.2*constant current-1.20*constant current (A)
Rated
Current of
inverter
b013
1 st electronic thermal
characteristic selection
00(reduced characteristic)/ 01(constant torque characteristic)/
02(free setting)
01
*b015
Free electronic thermal frequency
1
0.-400.(Hz) 0.
b016
Free electronic thermal current
1
0.0-1000.(A) 0.0
*b017
Free electronic thermal frequency
2
0.-400.(Hz) 0.
b018
Free electronic thermal current
2
0.0-1000. (A) 0.0
*b019
Free electronic thermal frequency
3
0.-400.(Hz) 0.
b020
Free electronic thermal current
3
0.0-1000.(A) 0.0
b021 Overload restriction selection
00(invalid)/01(enabled on acceleration / constant speed)/
02(enabled on constant speed)/03(enabled on acceleration / constant speed
(speed increasing at regenerating mode))
01
b022 Overload restriction level 0.50* rated current-2.00* rated current(A)
Rated
current
of
Inverter
x 1.50
b023 Overload restriction limit constant 0.10-30.00(s) 1.00
b024 Overload restriction 2 selection
00(invalid)/01(enabled on acceleration / constant speed)/
02(enabled on constant speed)/03(enabled on acceleration / constant speed
(speed increasing at regenerating mode))
01
b025 Overload restriction level 2 0.50*rated current-2.00*rated current(A)
Rated
current
of
Inverter
x 1.50
b026 Overload restriction constant 2 0.10-30.00(s) 1.00
b031 Software lock mode selection
00(impossible to change the data except this item when SFT terminal is
ON)/01(impossible to change the data except setting frequency item when SFT
terminal is ON)/02(impossible to change the data except this item)/
03(impossible to change the data except setting frequency item)/
10(possible to change data on operating)
01
adj
us
tabl
e fu
ncti
o
n
Ex
terna
l freq
uenc
y
adj
us
tmen
t
Accel. De
ce
l.
In
s
tantane
ous
powe
r f
a
ilur
e
r
e
s
tar
t
El
ectr
oni
c
t
h
er
m
a
l
Over
load l
im
it
Lock