Hitachi SJ300 Series - Manual (Page 27)

27
Chapter 3 – Parameter Setting Tables
Function mode
Code Function name Setting range Initial data remarks
C001 Intelligent input 1 setting 18(RS)
C002 Intelligent input 2 setting 15(SFT)
C003 Intelligent input 3 setting 09(2CH)
C004 Intelligent input 4 setting 11(FRS)
C005 Intelligent input 5 setting 04(CF3)
C006 Intelligent input 6 setting 03(CF2)
C007 Intelligent input 7 setting 02(CF1)
C008 Intelligent input 8 setting
01/(RV:Reverse is valid)/02(CF1:Multi-speed1)/ 03(CF2:Multi-speed2)/
04(CF3:Multi-speed3)/07(DB:External DC braking)/
09(2CH:two-stage adjustable speed)/ 11(FRS:Free-run)/
12(EXT:External trip)/13(USP:Unattended start protection)/
14(CS:commercial change)/15(SFT:software lock)/
16(AT:Analog input voltage/current select)/18(RS:Reset inverter)/
20(STA:3wire run)/ 21(STP:3wire keep)/ 22(F/R:3wire forward/reverse)/
26(CAS:Control gain switch function)/
31(OPE:Operating by operator select)/ 32(SF1:Multi-speed bit1)/
33(SF2:Multi-speed bit2)/ 34(SF3:Multi-speed bit3)/
35(SF4:Multi-speed bit4)/36(SF5:Multi speed bit5)/
37(SF6:Multi-speed bit6)/ 38(SF7:Multi-speed bit7)/
39(OLR:Overload restriction change) / 40(TL:Torque limit select)/
41(TRQ1:Torque limit switch 1)/42(TRQ2:Torque limit switch 2)/
43((PPI:P/PI switch)/44(BOK:Braking comformation)/
45(ORT:Orientation)/ 46(LAC:LAD cancel)/
47(PCLR:Position error clear)/ 48(STAT: Permission of pulse train)/
50(SSD:Torque bias hold)/52(ECM:Changeover in case of emergency)/
no (NO: No assign)
01(RV)
C011
Intelligent input 1 a/b (NO/NC)
selection
00(NO)/01(NC) 00
C012
Intelligent input 2 a/b (NO/NC)
selection
00(NO)/01(NC) 00
C013
Intelligent input 3 a/b (NO/NC)
selection
00(NO)/01(NC) 00
C014
Intelligent input 4 a/b (NO/NC)
selection
00(NO)/01(NC) 00
C015
Intelligent input 5 a/b (NO/NC)
selection
00(NO)/01(NC) 00
C016
Intelligent input 6 a/b
(NO/NC) selection
00(NO)/01(NC) 00
C017
Intelligent input 7a/b
(NO/NC) selection
00(NO)/01(NC) 00
C018
Intelligent input 8 a/b
(NO/NC) selection
00(NO)/01(NC) 00
C019
Input FW a/b (NO/NC)
Selection
00(NO)/01(NC) 00
C021 Intelligent output 11 setting 01(FA1)
C022 Intelligent output 12 setting 00(RUN)
C023 Intelligent output 13 setting 03(OL)
C024 Intelligent output 14 setting 19(BRK)
C025 Intelligent output 15 setting 21(ZS)
C026 Alarm relay output
00(RUN: running) / 01(FA1:Frequency arrival type1 signal) /
02(FA2:over setting frequency) / 03(OL: Overload advance notice signal)/
05(AL: Alarm signal)/06(FA3:Only setting frequency) /
07(OTQ: Over-torque signal) / 08(IP: On instantaneous stop) /
09(UV: Under voltage) / 10(TRQ: Torque limit)/
11(RNT: RUN time over) / 12(ONT:ON time over) / 13(THM: thermal caution) /
19(BRK: Brake release signal) / 20(BER: Brake error signal) /
21(ZS: Zero speed detect signal)/22(DSE: Speed error over signal) /
23(POK: Positioning completion signal)/24(FA4:Over frequency 2 signal)/
25(FA5: Only setting frequency) /
26(OL2: Overload advance notice signal (2)
(Intelligent output terminal 11-13 or 11-14 becomes AC0-AC2 or AC0-AC3
(Can: Alarm code output) forcibly when alarm code output is selected in C062)
05(AL)
C027 FM selection
00(Output frequency)/01(Output current) /02(Output torque)/
03(Digital output frequency)/04(Output voltage)/
05(Input electric power)/06(thermal load rate)/07(LAD frequency)
00
C028 AM selection
00(Output frequency)/01(Output current)/02(Output torque)/
04(Output voltage)/05(Input electric power)/06(thermal load rate)/
07(LAD frequency)
00
C029 AMI selection
00(Output frequency)/01(Output current)/02(Output torque)/
04(Output voltage)/05(Input electric power)/
06(Thermal load rate)/07(LAD frequency)
00
C031 Intelligent output 11 a/b 00(NO)/01(NC) 00
C032 Intelligent output 12 a/b 00(NO)/01(NC) 00
C033 Intelligent output 13 a/b 00(NO)/01(NC) 00
C034 Intelligent output 14 a/b 00(NO)/01(NC) 00
C035 Intelligent output 15 a/b 00(NO)/01(NC) 00
C036 Alarm relay output a/b 00(NO)/01(NC) 01
In
te
llig
en
t inp
u
t te
rmina
l se
tting
In
te
llig
en
t I
n
pu
t t
e
rmin
a
l a
c
tive
st
at
e set
ti
ng
In
te
llig
en
t o
u
tp
u
t te
rmin
a
l
se
tt
in
g
Analo
g
Ou
tpu
ts
O
u
tput t
e
rm
in
a
l s
tate s
e
tti
n
g
O
u
tput lev
e
l
s
e
tt
ing