Hitachi SJ300 Series - Manual (Page 29)

29
Chapter 3 – Parameter Setting Tables
Function mode
Code Function name Setting range Initial data remarks
b088
Resume on FRS cancellation
mode
00(0Hz start)/01(Start f-equaling) 00
b090 BRD usage ratio 0.0-100.0(%) 0.0
b091 Stop mode selection 00(deceleration stop)/01(Free-run stop) 00
b092 Cooling fan control
00(Always ON)/
01(ON during run, After power ON, then for 5 minutes on stop is implied.)
01
b095 BRD selection 00(invalid)/01(valid<invalid during stop>)/02(valid<valid during stop>) 00
b096 BRD ON level 330-380/660-760(V) 360/720
b098 Thermistor selection 00(invalid)/01(Positive temperature coefficient enable)/02 (NTC enable) 00
b099 Thermistor error level 0. – 9999. (ohm) 3000.
b120 Braking control selection 00(Invalid)/01(valid) 01
b121
Waiting time for releasing
braking conformation
0.00-5.00(s) 0.10
b122 Waiting time for acceleration 0.00-5.00(s) 0.40
b123 Waiting time for stop 0.00-5.00(s) 0.40
b124
Waiting time for signal
conformation
0.00-5.00(s) 0.00
*b125 Releasing frequency 0.00-99.99/100.0-400.0(Hz) 0.00
b126 Releasing current 0.00*rated current-2.00*rated current(A)
0.10* rated
current of
inverter
*b127 Brake OFF frequency 0.00-400.00Hz 0.00
b128
Delay time at brake signal is
turned OFF
0.00-5.00s 0.50
C091 Debug mode selection 00(No display)/01(Display) 00
C102 Reset selection
00(Trip cancel during ON)/01(Trip cancel during OFF)/
02(Valid only during trip<Cancel during ON>)
00
C111 Overload advance notice level 0.0-2.0*rated current(A)
Inverter rated
current
C121 O zero adjustment 0.-9999./1000-6553(10000-65530)
Set on
forwarding
C122 OI zero adjustment 0.-9999./1000-6553(10000-65530)
Set on
forwarding
C123 O2 zero adjustment 0.-9999./1000-6553(10000-65530)
Set on
forwarding
H001 Autotuning selection
00(Invalid)/01(Valid(the motor does not rotate))/
02(Valid(the motor rotates))
00
H002 1 st motor constant selection
00(Hitachi general purpose motor data)/01(Autotuning data)/
02(Autotuning data with online autotuning)
00
H003 1 st allowable motor selection 0.20-75.0(kW) <0.2-160kW>
Set on
forwarding
H004 1 st motor pole selection 2/4/6/8(pole) 4
H005 1 st speed response setting 0.001-9.999/10.00-65.53 4.00
H006 1 st stabilized factor 0. - 255. 100.
H020 1 st motor constant R1 0.000-9.999/10.00-65.53(ohm)
Set on
forwarding
H021 1 st motor constant R2 0.000-9.999/10.00-65.53(ohm)
Set on
forwarding
H022 1 st motor constant L 0.00-99.99/100.0-655.3(mH)
Set on
forwarding
H023 1 st motor constant I0 0.00-99.99/100.0-655.3(A)
Set on
forwarding
H024 1 st motor constant J 0.001-9.999/10.00-99.99/100.0-9999.(kgm
2
)
Set on
forwarding
H030
1 st motor constant R1
(Autotuning data)
0.000-9.999/10.00-65.53(ohm)
Set on
forwarding
H031
1 st motor constant R2
(Autotuning data)
0.000-9.999/10.00-65.53(ohm)
Set on
forwarding
H032
1 st motor constant L
(Autotuning data)
0.00-99.99/100.0-655.3(mH)
Set on
forwarding
H033
1 st motor constant I0
(Autotuning data)
0.00-99.99/100.0-655.3(A)
Set on
forwarding
H034 1 st motor constant J 0.001-9.999/10.00-99.99/100.0-9999.(kgm
2
)
Set on
forwarding
H050
1 st PI-control proportion gain
setting
0.00-99.99/100.0-999.9/1000.(%) 100.0
H051
1 st PI-control integration gain
setting
0.00-99.99/100.0-999.9/1000.(%) 100.0
H052
1 st P-control proportion gain
setting
0.01-10.00 1.00
H060 1 st 0Hz-SLV limiter setting 0.-100.(%) 100.
H070
PI-control proportion gain for
switching
0.00-99.99/100.0-999.9/1000.(%) 100.0
H071
PI-control integration gain for
switching
0.00-99.99/100.0-999.9/1000.(%) 100.0
H072
P-control proportion gain for
switching
0.00-10.00 1.00
Miscel
laneou
s
Mot
o
r C
o
n
s
ta
nt
s