Document Outline

• Contents
• About This Document
  • Important . . . Read This Before Proceeding!
    • Use of Warnings and Cautions
    • EC Declaration of Conformity (DOC)
• Introduction
  • Features
  • System Description
  • Appropriate Applications and Limitations
    • Examples: Appropriate Applications
    • Examples: Inappropriate Applications
  • Control Reliability and Safety Categories
  • Operating Features
    • Trip/Latch Output
    • Wiring Options for Emitter/Receiver Swapability
    • Manual Reset/Remote Test Input and EDM
      • External Device Monitoring (EDM)
    • Status Indicators
• Mechanical Installation
  • Pre-Installation Considerations
    • Calculating the Safety Distance (Minimum Distance)
      • EZ-SCREEN Type 2 Models With Response Times
      • Formula and Examples
        • Examples
    • Reducing or Eliminating Pass-Through Hazards
    • Supplemental Safeguarding
    • Other Considerations
      • Reset Switch Location
      • Adjacent Reflective Surfaces
      • Use of Corner Mirrors
      • Emitter and Receiver Orientation
      • Installation of Multiple Systems
  • Mounting System Components
    • Overview of Emitter/Receiver Mounting Hardware
      • Mounting Hardware
      • Using Center Mounting Brackets
    • Mounting and Initial Alignment of Emitter/Receiver Pairs
      • Verifying Initial Emitter/Receiver Alignment
• Electrical Installation and Testing
  • Routing Cordsets
  • Initial Electrical Connections
  • Initial Checkout Procedure
    • Configuring the System for Initial Checkout
    • Initial Power-Up
    • Optical Alignment
      • Optical Alignment Procedure with Mirrors
    • Trip Test
  • Electrical Connections to the Guarded Machine
    • OSSD Output Connections
    • FSD Interfacing Connections
      • Protective Stop (Safety Stop) Circuits
      • Dual-Channel Control
      • Single-Channel Control
    • Machine Primary Control Elements
    • Manual Reset/Remote Test Input and EDM
      • Manual Reset/System Test Procedure
      • Manual Reset
      • Remote (External) Test
      • External Device Monitoring Hookup
    • Preparing for System Operation
    • Commissioning Checkout
  • Reference Wiring Diagrams
    • Generic Emitter Wiring Diagram
    • Generic Wiring to FSDs (manual reset)
    • Generic Wiring — Interface Module (2-Channel EDM, Manual Reset)
• System Operation
  • Security Protocol
  • Reset Procedures
    • Receiver Resets
    • Emitter Resets
  • Status Indicators
    • Emitter
    • Receiver
      • Alignment Indicators
      • Status Indicators
  • Normal Operation
    • System Power-Up
    • Run Mode
    • Manual Reset Procedure
  • Periodic Checkout Requirements
• Troubleshooting and Maintenance
  • Troubleshooting and Lockout Conditions
  • Recovery Procedures
    • Receiver (System Reset)
    • Emitter Reset
  • Electrical and Optical Noise
    • Sources of Electrical Noise
    • Sources of Optical Noise
  • Servicing and Maintenance
    • Cleaning
    • Warranty Service
    • Disposal
• Checkout Procedure Schedule
  • Schedule of Checkouts
• Specifications and Accessories
  • Specifications
    • General Specifications
    • Emitter Specifications
    • Receiver Specifications
    • Emitter and Receiver Dimensions
    • Bracket Dimensions
      • Standard End Cap Brackets
      • Standard Center Brackets
  • Accessories
    • Cordsets
      • Single-Ended (Machine Interface) Cordsets
      • Double-Ended Cables
      • Splitter Cordsets
    • Interface Modules
    • Contactors
    • Lens Shield
    • EZ-LIGHT™ for EZ-SCREEN®
    • MSA Series Stands (Base Included)*
    • MSM Series Corner Mirrors
    • SSM Series Corner Mirrors
    • Accessory Mounting Brackets
    • Alignment Aids
    • Replacement Parts
    • Documentation
• Standards and Regulations
  • U.S. Application Standards
  • OSHA Regulations
  • International/European Standards
  • Sources of Standards and Regulations
  • Contact Us
• Glossary
• Index