Document Outline

• M3099GX/GH IMAGE SCANNER OEM MANUAL
• Preface
• Conventions
• Contents
  • Figures
  • Tables
• OVERVIEW
• Scanner Types
• Features
• Configuration
  • Configuration of the scanner
  • Arrangement of units
• Operation Overview
  • Operation of the mechanism unit
  • Operation of the control unit
  • Resolution
• SPECIFICATIONS
• General
• Electrical Specifications
• Environmental Specifications
• Physical Specifications
• Option Specifications
• INTERFACE
• Physical Specifications
  • SCSI Bus (See ANSI SCSI-2 4.5)
  • SCSI Bus Signals (See ANSI SCSI-2 4.6)
  • Signal Values
  • Signal Source
  • SCSI Bus Timing
    • Arbitration Delay
    • Assertion period
    • Bus Clear Delay
    • Bus Free Delay
    • Bus Set Delay
    • Bus Settle Delay
    • Cable Skew Delay
    • Data Release Delay
    • Deskew Delay
    • Disconnection Delay
    • Hold Time
    • Negation Period
    • Power-On to Selection Time
    • Reset to Selection Time
    • Reset Hold Time
    • Selection Abort Time
    • Selection Time-out Delay
    • Transfer Period
• SCSI Bus Phases
  • BUS FREE Phase (See ANSI SCSI-2 6.1.1 for details)
  • ARBITRATION Phase
  • SELECTION Phase
  • RESELECTION Phase
    • RESELECTION
  • Information Transfer Phases
    • Asynchronous Information Transfer
    • Synchronous Data Transfer
  • COMMAND Phase
  • Data Phase
    • DATA IN Phase
    • DATA OUT Phase
  • STATUS Phase
  • Message Phase
    • MESSAGE IN Phase
    • MESSAGE OUT Phase (See ANSI SCSI-2 6.1.9.2 for details)
• SCSI Bus Conditions
  • Attention Condition
  • Reset Condition
• SCSI Bus Phases Sequences
• Commands (See ANSI SCSI-2 7)
  • RESERVE UNIT Command
    • Superseding Reservations
  • RELEASE UNIT Command
  • TEST UNIT READY Command
  • INQUIRY Command (See ANSI SCSI-2 7.2.5)
    • Standard INQUIRY Data (See ANSI SCSI-2 7.2.5.1)
    • Vital Product Data
  • REQUEST SENSE Command (See ANSI SCSI-2 8.2.14)
  • SEND DIAGNOSTIC Command
  • SET WINDOW Command
    • Vendor Unique Parameters
  • OBJECT POSITION
  • SEND Command
  • SCAN Command
  • READ Command
  • MODE SELECT(6) Command
  • MODE SENSE(6) Command
    • Mode Parameter
  • ENDORSER Command (ENDORSER option is required)
• Status (See ANSI SCSI-2 7.3)
• Message(See ANSI SCSI-2 6.5)
  • ABORT (Init Æ Targ)
  • BUS DEVICE RESET (Init Æ Targ)
  • COMMAND COMPLETE (Init ¨ Targ)
  • DISCONNECT (Init ¨ Targ)
  • IDENTIFY (Init Æ Targ)
  • INITIATOR DETECTED ERROR (Init Æ Targ)
  • MESSAGE PARITY ERROR (Init Æ Targ)
  • MESSAGE REJECT (Init ´ Targ)
  • NO OPERATION (Init Æ Targ)
  • RESTORE POINTERS (Init ¨ Targ)
  • SAVE DATA POINTER (Init ¨ Targ)
  • SYNCHRONOUS DATA TRANSFER REQUEST
• Command Sequence
  • System Initialization
  • General Procedure for Initializing Devices
  • Verify State Test
  • Scanning Sequence
    • Basic Scanning Sequence (Simplex Mode)
    • Duplex Scanning
    • Endorser Control
  • READ command sequences and phase progression
    • Multiple READ (disconnect disabled)
    • Multiple READ (disconnect enabled)
• BASIC OPERATION
• Power Switch Operation
• Opening the Upper Transport Unit
• Closing the Upper Transport Unit
• Operator Panel
  • Operator panel function
  • LCD display
  • Buttons
  • Message List
• Loading Document
• Lamp Replacement
• Roller ASY Replacement
• Pick Roller Replacement
• Belt Replacement
• Pad Replacement
• ERROR PROCESSING AND RECOVERY
• Device and Operator Actions for Temporary Errors
• Device and Operator Actions for Equipment Errors
• DOCUMENT SPECIFICATION
• Document Size
• Document Quality
  • Document type
  • Ream weight
  • Precautions
• Document Limitations
  • Areas that must not be perforated
  • Print prohibit areas the front and back surfaces
• Grounding Color Area
• Drop-out Color
  • Print density measurement
  • Drop-out color standards
• Job Separation Sheet
  • Shape
  • Document type
• CONSUMABLES AND ACCESSORIES
• Consumables
• Accessories
• CLEANING
• Cleaning Locations and Frequencies
• Cleaning Tools
• Procedure
  • Cleaning the front-side lamp
  • Cleaning the rollers
  • Cleaning the transport paths
  • Cleaning the glass surface
  • Cleaning the sensors
• ENDORSER
• A1. Specifications
• A2. Panel operation
  • A2.1 How to set the endorser ON (or OFF)
  • A2.2 How to set the initial number
  • A2.3 How to set the print number reset condition
  • A2.4 How to reset the print number manually
  • A2.5 How to reset the print head life counter
  • A2.6 How to test the printing by the operator panel operation
• A3. Print head handling
  • A3.1 Replacing the print head
  • A3.2 Print head position adjustment
• SETUP MODE
• B.1 Activating the setup mode
• B.2 Operational transition in the setup mode
• B.3 Contents of the setup mode
  • B3.1 Setting double-feed detection
  • B3.2 Setting IPC-2 pre-set mode
  • B3.3 Reset of abrasion counter
  • B3.4 Setting buzzer
  • B3.5 Setting pre-pick
  • B3.6 Adjusting LCD contrast
  • B3.7 Setting pick speed
  • B3.8 Setting initial value of endorser
  • B3.9 Setting reset method of endorser
  • B3.10 Reset of endorser
  • B3.11 Reset of ink counter
  • B3.12 Setting SCSI-ID
  • B3.13 Setting Product-ID
  • B3.14 Setting picking start time
  • B3.15 Setting picking time
  • B3.16 Setting time-out limit
  • B3.17 Setting hopper time
  • B3.18 Setting heater control
• SEPARATION PRESSURE ADJUSTMENT
• Glossary of Terms
• Index
• Reader Comment Form