Great Plains 3N-4025P Operator Manual Instruction Manuals and User Guides
We have 2 Instruction Manuals and User Guides for 3N-4025P Operator Manual Great Plains
Manuals
Read manual
| Recognized languages: | English |
|---|---|
| Pages: | 134 |
| Size: | 27.03 MB |
| Recognized languages: | English |
|---|---|
| Pages: | 194 |
| Size: | 23.65 MB |
Show table of contents
Read manual
Document Outline
- Important Safety Information
- Look for Safety Symbol
- Be Aware of Signal Words
- Prepare for Emergencies
- Be Familiar with Safety Decals
- Wear Protective Equipment
- Handle Chemicals Properly
- Avoid High Pressure Fluids
- Use A Safety Chain
- Check for Overhead Lines
- Keep Riders Off Machinery
- Use Safety Lights and Devices
- Transport Machinery Safely
- Shutdown and Storage
- Practice Safe Maintenance
- Tire Safety
- Safety At All Times
- Safety Decals
- Safety Reflectors and Decals
- 818-055C Slow Moving Vehicle Reflector
- 838-266C Red Reflectors
- 838-265C Amber Reflectors
- 838-267C Daytime Reflectors
- 818-557C Danger: Cannot Read English
- 818-590C Danger: Crushing Hazard
- 838-102C Danger: Falling Hazard
- 818-045C Warning: Pinch/Crush
- 818-188C Warning: Speed Hazard
- 818-339C Warning: High Pressure Fluid Hazard
- 818-579C (Option) Warning: Pinch Point
- 818-580C (Option) Warning: Overhead Hazard
- 818-398C Caution: Tires Not A Step
- 818-587C Caution: General
- 838-426C Caution: Pressure/Torque
- Introduction
- Preparation and Setup
- Operating Instructions
- Hydraulic Drive Operation
- Adjustments
- Planting Depth
- Frame Level
- Frame Height
- Frame Height without Frame-Mounted Coulters
- Frame-Mounted Coulters
- Row Unit Shut-Off
- Finger Meter Sprocket Indexing (Stagger)
- Implement Lift Switch Adjustment
- Frame Weight
- Marker Adjustments
- 10P Series Row Unit Adjustments
- 10HD Series Row Unit Adjustments
- 20P Series Row-Unit Adjustments
- 25 Series Row-Unit Adjustments
- Troubleshooting
- Maintenance and Lubrication
- Welding
- Cleaning Out Meters
- 10 and 20 Series Meter Slide Maintenance
- Frame Alignment and Level
- Tongue Spacer Block
- Bleeding Hydraulics
- Marker Maintenance
- Electric Clutch Lockup
- Hydraulic Drive Maintenance
- Row Unit Maintenance
- Lubrication
- Grease Bank (Option)
- Parallel Arm Pivots
- Wing Caster Wheel Pivot
- Rock shaft
- Lift Cylinder Pins
- Wing Flex Pivots
- Rear Axle Pivot
- Transfer Drive Shafts
- Wing Frame Vertical Pivots
- Marker(s) (Option)
- 20 Series Side Gauge Wheel Bushings
- Rear Wheel Caster Spindles
- Drive Chains
- Coulter Hub Bearings
- Marker Disk Bearings (Option)
- Wheel Bearings
- Options
- Hitch Options
- Flat Fold Markers
- Dual Weight Kit
- Frame-Mounted Coulters
- Coulter Tines
- Baffle Kits
- Seed Tube Plug
- Row Unit Options
- Available Down Force See Adjustments pages
- Row Lock-Up Pin (page 164)
- Unit-Mount Coulter (page 165)
- Row Cleaner (page 90)
- Meter Type (page 165)
- Singulator Plus Meter (page 165)
- Singulator Plus Wheel (page 166)
- 6- or 12-Finger Meters (page 84)
- Side Depth Gauge Wheel
- Gauge Wheel Scraper (page 168)
- Inside Scraper (page 167)
- Seed-Lok® Firmer
- Keeton® Firmer
- 10HD and 25 Series Lock-Up Pin
- 10HD and 25 Series Unit-Mounted Coulters
- 15 in.Coulter Blades
- Seed Meters
- Seed Meter Wheels
- Inside Carbide Scrapers
- 20 Series Gauge Wheel Scraper
- 25 Series Gauge Wheel Scrapers
- Seed Firmers
- Press Wheels
- Appendix
- Index