Document Outline

• SAFETY INSTRUCTIONS
  • Safety Symbols
  • Safety Guidelines
    • Power cord for the United Kingdom
• GETTING STARTED
  • GDM-8200A Series Lineup
  • GDM-8200A Series Characteristics
  • Front Panel Overview
    • Measurement keys (Upper row)
    • Measurement keys (Lower row)
  • Rear Panel Overview
  • Set Up
    • Tilt Stand
    • Power Up
• BASIC MEASUREMENT
  • Basic Measurement Overview
    • Common attribute: refresh rate
    • Common attribute: reading indicator
    • Common attribute: manual/automatic triggering
  • AC/DC/AC+DC Voltage Measurement
    • Select Voltage range
    • Voltage conversion table
    • Crest factor table
  • AC/DC/AC+DC Current Measurement
    • Select Current range
  • 2W/4W Resistance Measurement
    • Select Resistance range
  • Diode Test
  • Continuity Test
    • Set continuity threshold
    • Select beeper setting
  • Frequency/Period Measurement
  • Temperature Measurement
    • Select thermocouple type
    • Set reference junction temperature
• ADVANCED MEASUREMENT
  • Advanced Measurement Overview
    • Common attribute: refresh rate
    • Common attribute: reading indicator
    • Common attribute: manual/automatic triggering
  • dBm/dB Measurement
    • Measure dBm
    • Measure dB
  • Max/Min Measurement
  • Relative Value Measurement
  • Hold Measurement
  • Compare Measurement
  • Math Measurement
    • Measure MX+B
    • Measure 1/X
    • Measure Percentage
  • Dual Display Measurement
• SYSTEM/DISPLAY CONFIGURATION
  • Refresh Rate Setting
  • Trigger Setting
    • Manual/Automatic triggering
    • Use external trigger
    • Set trigger delay
  • Digital Filter Setting
    • Overview
    • Filter setting
  • Display Setting
    • Display light setting
    • Display on/off setting (+ key lock)
• STORE/RECALL
  • Store Measurement Record
  • Recall Measurement Record
  • Save Instrument Settings
  • Recall Instrument Settings
• SCANNER (OPTIONAL)
  • GDM-SC1 Scanner Specifications
  • Scanner Installation
    • Configure scanner
    • Select Channel group and enable scanner
    • Connect wire
    • Insert scanner
    • Scanner Configuration Record
  • Setup Scan
    • Overview
    • Setup Simple Scan
    • Setup Advanced Scan
    • Use external trigger
  • Run Scan
    • Overview
    • Run Scan/Step
    • Recall Scan/Step result
    • Setup and run monitoring
• DIGITAL I/O
  • Digital I/O Terminal Configuration
    • Application: Compare measurement
    • Application: External trigger
• REMOTE CONTROL
  • Configure Interface
    • Overview
    • Configure USB interface
    • Configure RS-232C interface
  • Command Syntax
  • Command Set
    • CONFigure command
    • SENSe command
    • UNIT command
    • CALCulate command
    • TRIGger command
    • SYStem related command
    • STAtus reporting command
    • RS-232C interface command
    • IEEE 488.2 common command
    • ROUTe command
    • Secondary display: CONFigure2 command
• FAQ
  • What is the Output key used for?
  • I pressed the EXIT key but cannot get out of Scanner mode.
  • The GDM-8200A series performance does not match the specifications.
• APPENDIX
  • Firmware Version
  • Fuse Replacement
    • Replace AC source fuse
    • Replace input current fuse
  • Specifications
    • General
    • Reading rates (readings/sec)
    • DC Voltage
    • AC Voltage
    • DC Current
    • AC Current
    • 2W Resistance
    • 4W Resistance
    • Diode/Continuity
    • Frequency
    • Temperature
    • Optional Scanner
  • EC Declaration of Conformity
• INDEX