Document Outline

• FOREWORD
• SAFETY ALERT SYMBOLS AND SAFETY SIGNAL WORDS
• REVISION LOG
• TABLE OF CONTENTS
• Section 1. safety precautions
  • 1.1 GENERAL
  • 1.2 PRE-OPERATION
    • Operator Training And Knowledge
    • Workplace Inspection
    • Machine Inspection
  • 1.3 OPERATION
    • General
    • Trip and Fall Hazard
    • Electrocution Hazard
    • Tipping Hazard
    • Crushing And Collision Hazard
  • 1.4 Towing, Lifting, And Hauling
• Section 2. preparation and inspection
  • 2.1 Personnel Training
    • Operator Training
    • Training Supervision
    • Operator Responsibility
  • 2.2 Preparation, Inspection, and Maintenance
  • 2.3 Pre-Start Inspection
  • 2.4 Daily Walk-Around Inspection
  • 2.5 Function Check
• Section 3. machine Controls, Indicators and operation
  • 3.1 general
  • 3.2 machine description
  • 3.3 machine operation
    • Getting Started
  • 3.4 Battery Charging
    • Battery Low Voltage Warning Indicators
    • To Charge Batteries
    • Battery Charging Status Indicators
  • 3.5 Ground Control Station - operation
    • Main Power Selector Switch
    • Emergency Stop/Shut Down Button
    • Master Disconnect Switch - (EE Option Only)
    • Brake Release Button
    • Platform Up
    • Platform Down
    • Manual Descent Control Valve
    • Machine Status LCD Display
    • LCD Display Fault Conditions
  • 3.6 Ground Control Station - Programming
    • General
    • Programming Levels
    • Operator Programming Mode
    • Activating Programming Mode
    • Entering Password
    • Programming Mode Selection
    • Selecting Programmable Item to Adjust
    • Adjusting Programmable Setting
  • 3.7 Platform Control Console Operation - (Machines Serial Number - 0130007616 to present)
    • General
    • Platform On/Off Key Switch
    • Platform Emergency Stop/Shut Down Button
    • Platform Control Display Panel
    • Drive/Lift Mode Selector Switch
    • Horn Button
    • Joystick Function Enable Lever
    • Multifunction Joystick Control
    • Drive Mode
    • Lift Mode
    • Drive Speed Setting Controls
  • 3.8 Platform Control console OPERATION - (Machines before Serial Number - 0130007616)
    • At Ground Control Station
    • Emergency Stop/Shut-Down Button
    • Battery Charge/Fault Code LED Indicator
    • Driving Machine
    • Adjusting Maximum Drive Speed Control
    • Elevating/Lowering the Platform
  • 3.9 Parking Machine
  • 3.10 Progammable Security Lock (PSL™) (DVL/DVSP - Option)
    • PSL™ Box and Ground Control Locations
    • Machine Power Up using the PSL™
    • Machine Power Down
    • Changing the Operator’s Code
  • 3.11 Platform Configurations
    • StockPicking Platform Operation
  • 3.12 Fall Protection - Lanyard Attachment
  • 3.13 quick-change platform mounting
    • Platform Removal
    • Platform Installation
  • 3.14 Obstruction Sensing System (DVSP - Option)
    • System Description
    • Operation
    • OSS Pre-Start Inspection
  • 3.15 TRANSPORTING, LIFTING AND TIE DOWN PROCEDURES
    • General
    • Truck Transport
    • Machine Tie-Down
    • Crane Hook Accessory (DVL Option)
    • Fork-Lift Truck Transport
  • 3.16 Rug Carrier Accessory (DVSP - option)
    • General
    • Pre-Start Inspection
    • Hanging a Rug using the Rug Carrier Accessory Arms
    • Removing a Rug using Rug Carrier Accessory Arms
  • 3.17 Stock-Picker Hanger Accessory
    • Pre-Start Inspection
    • Loading and Transporting an Item using the Hanger Accessory
• Section 4. emergency procedures
  • 4.1 general information
  • 4.2 emergency operation
    • Operator Unable to Control Machine
    • Platform Caught Overhead
  • 4.3 INCIDENT NOTIFICATION
• Section 5. General Specifications and Operator Maintenance
  • 5.1 Introduction
  • 5.2 General Specifications
    • Machine Specifications
    • Electrical Specifications
    • Platform Data
    • Machine Component Weights
    • Serial Number Locations
  • 5.3 Operator maintenance
    • Lubrication
• Section 6. INSPECTION AND REPAIR LOG