Document Outline

• OPERATING INSTRUCTIONS
• Model No. CF-E1M
  • Introduction
  • Illustrations in this Manual
    • NOTE:
    • CAUTION:
    • WARNING:
  • ( Enter 1 :
  • Copyright
  • Disclaimer
  • Trademarks
• Read Me First
  • Federal Communications Commission Radio Frequency Interference Statement
  • Warning
  • FCC Regulation Notice for modem
  • Read Me First
    • Usage
    • Handling
  • Read Me First
    • Saving Data on the Hard Disk
    • Saving Data on Floppy Disks
      • Write-protect Tab ^
      • Write Disable
    • Computer Viruses
    • Restrictions when starting a program in the MS-DOS mode
    • Maintenance
      • Areas Excluding the Display
      • LCD Display
    • About System File Checker
• Names and Functions of Parts
  • Reset Button | ^
  • RAM Module Slot
  • USB Ports I
  • Optical Digital Audio Output Terminal
  • Dust Protection Cap
  • Names and Functions of Parts
• First-time Operation
  • 1 Confirm the inclusion of all parts
    • Keyboard
    • Mouse
    • Floppy Disk Drive .... 1
    • AC Cord 1
    • Modem Telephone CaUe.. 1
    • Clamper
    • Eject Pin
    • Operating
    • Instructions 1
    • Product Recovery CD-ROM 1
    • Windows® Book
    • WinDVD™2000 CD-ROM
    • Sheet ForWinDVD™2000
  • First-time Operation
    • Write Down the Product Key Code
    • Connect the keyboard and mouse to the USB ports.
    • Read the LIMITED USE LICENSE AGREEMENT (o- page 59)
    • Set the stand for the keyboard
      • Stand
      • Power Indicator
    • Turn your computer on
  • First-time Operation
    • 8 Setup Windows 98
    • Q Computer power off
• Using the Mouse
  • Basic Operation
    • Function
    • Operation
    • Moving the Cursor
    • Clicking
    • Double-Clicking
    • Dragging
    • How to advance (scroll button) ^
• Starting Up/Shutting Down
  • Starting Up
    • Power Switch
    • When peripheral devices (e.g., Printer) are connected, turn on the power of each of these devices first
    • Turn your computer on
    • If the message "Enter your Password" is displayed,
      • Will Not Start*
    • When an application or file that was previously displayed appears on your screen,
  • Shutting Down (power off your computer)
    • Confirm that 0; is displayed on the taskbar
    • Turn your computer off
  • starting Up / Shutting Down
    • Starting UpYour Computer Quickly
      • Sleep Switch
    • Enter the Hibernation Mode With the Sleep Switch 1 Press the sleep switch
    • Enter the Hibernation Mode By Selecting [Stand by]
      • Select [Start] - [Shut Down] Select [Stand by]
        • ■0 Click [Stand by]
        • (D Click [OK]
    • Resuming From the Hibernation Mode
• Conserving Power
  • Setting Power Management
    • 1 Select [Start]-[Settings]-[Control Panel]-[Power Management]
    • 2 Select [Power Schemes]
      • ■0 Click |F| and select the setting
      • and set the time for each
      • (D Click [OK]
    • # If the computer screen turns off
    • When the screen does not return to the original screen even with the above operation
    • Power on the computer by holding the power switch down for approximately one second.
• Setting the Sound Volume
  • Using the Audio Mixer
    • Select ^ from the taskbar
  • Making Settings In the Control Panel
    • 7 Select [Start] - [Settings] - [Control Panel] 2 Select [YAMAHA DS-XG Audio Config]
    • NOTE>
    • After setting each item, click [OK]
• DVD-ROM Drive
  • Usage Precaution
    • To avoid damaging discs:
  • Using the DVD-ROM Drive
    • Title side up
    • 1 Confirm the computer is powered on, press the eject button lightly
      • Recessed Manual Disc Eject Button
    • Place a disc / Remove a disc
    • Close the disc tray by pressing the eject button
• Modem
  • Connecting to a Telephone Line and Settings 1 Connecting a telephone line to the internal modem
  • 2 Select [Dialing Properties] in [Start] - [Settings] - [Control Panel] - [Modems]
• VisualBright
  • When you want to turn this feature off
    • Maximized high image quality display 1
    • 10% of the width of the window
• Using USB Devices
  • When Installing a New Device Driver
  • Using the Floppy Disk Drive
    • 1 Connecting a floppy disk drive.
  • Inserting / Removing the Floppy Disk
    • Using USB Devices (e.g., Floppy Disk Drive, Printer)
  • Using the Printer
    • 1 Connect the printer to your computer.
    • NOTE>
    • Turn on the printer, then turn on the computer.
    • Setting your printer.
• Using PC Cards
  • When inserting a card
    • Press the ejection button and remove the dummy card (g* below)
    • Set the labeled side of the PC Card to the rear of the display and slide the card firmly into the slot
  • Removing the PC Card
    • Select [Start] - [Settings] - [Control Panel] - [PC Card (PCMCIA)]
    • Select the PC Card slot and select [Stop], then select [OK]
    • When the message [You may safety remove this device.] is displayed, click [OK]
    • Press the button and slide the PC Card out
• Using Audio Devices
  • Microphone / Headphone / Speaker
  • Optical Digital Audio Output Terminal
    • To connect a device, perform the following steps:
• Adding Memory
  • After completing operations and power off the computer (page 17), remove the AC cord
  • Set the computer so that the display is facing downwards Using a small-sized Philips screwdriver, remove the four screws
    • Soft Cloth
  • Adding Memory
    • 4 Remove the four screws of the stand and then remove the cabi- net
    • 5 Remove the RAM Module Cover
    • 6 Inserting / Removing the RAM module <When inserting a module>
    • <When removing a module>
    • Repiace the cover and screws removed in Steps 3to 5
• DV Capture
  • Connecting a Digital Video Camcorder
    • Turn on the computer and the digital video camcorder (c^ page 13)
    • • When capturing recorded contents
    • • When capturing input from a digital video camcorder
    • After confirming Windows has started up, connect a digital video camcorder to the computer with a DV interface cable
      • DV Input/Output Connector
      • ^ IEEE 1394 Inter¬
      • face Connector
  • When Removing the Digital Video Camcorder
  • Before Running DV Capture
  • Running DV Capture
    • Confirm that the digital video camcorder is properly connected
    • Select [DV Capture] icon on the desktop
  • DV Capture
    • Movie Capture
      • Running DV Capture (c? page 37)
      • Playing the tape and then perform moving images capture as follows
        • ® Confirm that "DV" is displayed
        • Click n.
        • Click [MOVIE CAPTURE] to begin capture
        • Click again to end the capture
        • or, click
      • About capturing
        • 1:08’14 p.m.
      • Select '"g": to stop the playback
    • Playing Captured Movie Files
      • Running DV Capture {or page 37)
        • (D Confirm that the display changes to [FILE] from [DV]
        • ■ Click
        • @ Click
  • DV Capture
    • 9 When selecting a file to be played from the ImageBrowser 1 Select [IMAGEBROWSER] from the [DV Capture] window
      • © Click
    • still Capture
      • Running DV Capture {a= page 37)
      • Play the tape and then perform still image capture
        • © Confirm that "DV" is displayed
        • Click
        • — (© Click [STILL CAPTURE] for the scene to capture
    • Viewing Still Image Files
  • DV Capture
    • Detailed Settings for Stili Image Capturing
      • Running DV Capture {o= page 37)
      • Select [Settings] and then [Still Settings] Make the still image settings and click [OK]
        • Select the size.
        • Select the color option of the image.
        • Select the format to save the image in (i.e., either JPEG or BMP).
    • Changing the destination folder and file name
      • It is possible to change the destination folder.
      • Auto create
      • -User Customize
• Using Image Files
  • NOTE>
  • Running ImageBrowser
    • Select [IMAGEBROWSER] icon on the desktop
      • Display of a single image
      • Activation of Movie Messenger {Or’ page 47)
      • Display of moving images
      • Sending mail
  • Using Image Files
    • Displaying Images
      • For a single image (*.BMP)
      • For a still image (*.JPG)
      • For a moving image (*.AVI)
    • About the menu commands of ImageBrowser
    • Sending Image Files By Mail
    • Mail software settings
      • Running ImageBrowser (co page 43)
      • Click [E-mail Settings] under the [Settings] menu and make the settings
        • 0 Select a mail application to use
      • When using a non-MAPI software application
      • When using Outlook Express or Outlook 97/98
  • Using Image Files
    • Sending Mail From a List
      • 1 Running ImageBrowser (c^ page 43)
        • 0 Click the still image to send by mail
      • Write a message and then send the mail
    • Compressing and Mailing Moving Images (Movie Messenger)
      • 1 Open Movie Messenger from the ImageBrowser (c^ page 43)
        • 0 Click
        • Click the still form of a moving image to send by mail
        • Double Click
      • Make the compression settings and compress the file
        • 0 Make the compression settings
        • Click [Compress]
  • Using Image Files
    • Run the mail software
      • ® Click [Play]
      • Click [E-mail]
• Setup Utility
  • Running the Setup Utility
    • 1 Turn on your computer by pressing the Power Switch or restart using the [Start]-[Shut Down]
    • 2 When [Press <F2> to enter SETUP] message is displayed, press
    • 9 Closing the Setup Utility
    • 1 Using [ ^-l and Q , select [Exit] menu and then press [Enter!
  • Setup Utility
    • Main Menu
      • 1 Select [Main] menu with [ ^ I [ -» I keys
    • Security Menu
      • 1 Using [ <-1 and i -► 1, select [Security] menu
      • 2 Set the User Password
      • 3 At the [Setup Notice], press [Enter]
• List of Error Codes
• Dealing With Problems
  • # When the display freezes
  • <When the keyboard and mouse work>
    • (D Click the application for which [No response] is shown from the list of applications, and then click [End Task}.
    • (3) When the confirmation message for “Close” appears, click [Close].
    • 0 If the [Close Program] window is not displayed or the application^
    • cannot be ciosed after a period of more than 30 seconds, press [ Ctrl ]+ (3D +1 Del) again.
  • <When the keyboard and/or mouse does not work>
• Troubleshooting Suggestions
  • Starting Up
  • Operations
  • Troubleshooting Suggestions
    • Operations
    • Display
    • Character Input
    • Disk Operations
      • Recessed Manual Disc Eject Button
    • Communication
  • Troubleshooting Suggestions
    • Connecting Peripherals
    • System File Checker
• Reinstalling Software
  • Before Reinstallation
    • Turn the computer on
    • When [Press <F2> to enter SETUP] message is displayed, press
    • ni Set the Product Recovery CD-ROM in the DVD-ROM drive 4 Restart the computer by pressing [ Ctrl) + [ Alt] + (Del ]
  • Reinstallation
    • When the [Panasonic] logo is displayed in the center of the screen, press Î Esc]
    • 2 Select [2. DVD Drive] using the m and CE) keys from the [Startup menu], and then press Î Enter]
    • 3 Make a selection from the menu
  • Reinstalling Software
    • At the confirmation message “[Y,N]?” press (Y)
    • Remove the Product Recovery CD-ROM, then close the tray
    • Restart the computer by pressingf Ctrl ] + [Alt] + [ Del 1, and perform the setup procedure for Windows by following the instructions on the screen (g* page 14)
      • LICENSE
      • TERM
• Installing Windows 98 Related Files
  • 1 Install the driver to use the DVD-ROM drive in the MS-DOS mode
  • 2 Turn the computer on
  • 3 If the [Panasonic] logo disappears, immediately press C Ctrl ] key (until the menu is displayed)
  • Select [Command prompt only]
  • Set the Product Recovery CD-ROM in the DVD-ROM drive After C:\>, type in the following
  • Follow the on-screen instructions
• Specifications
  • Main Specifications
  • Other Specifications
  • For U.S.A.