JVC BR-D95U - Manual (Page 51)

100
10-3 TIME CODE RECORDING
10 HOW TO USE TIME CODE
Front sub panel
Notes
● Drop/Non-drop Frame
mode selection (NTSC
only)
Automatically selected
according to the mode of
the received time code
(Drop Frame or Non-drop
Frame).
● Regeneration operation
• When time code is being
regenerated with input
time code, the built-in time
code generator stops
counting when no time
code is input.
● In the Play mode, time
code regeneration is based
on the playback time code
value.
● Inserting time code
If only time code data is
being inserted, record it on
the main time code. It is not
possible to insert it in the
sub time code.
1. Front sub panel switch setting
● Select the External Time Code Generator mode by setting the [INT/EXT]
switch to “EXT”.
The [FREE/REC] and [PRESET/REGEN] switch settings are not necessary.
● Select the Counter Display or On-screen Display mode to TC or UB with the
[COUNTER] and [SHIFT] buttons.
2. Menu switch setting
● Select the external time code to be regenerated.
● Menu switch No. 409 <EXT REGEN TC> (Initial setting: LTC (0))
LTC (0): Regenerates the LTC time code input through the rear panel
[TC IN] connector.
Input LTC time code should be regenerated (matched in
terms of sync and phase) with video signals. Make sure you
input an external sync signal to the feeding equipment.
VITC (1): Regenerates the VITC time code superimposed on the video
signal input through the rear panel VIDEO IN connector.
● User bit data selection
● Menu switch No. 457 <UB PRESET AUTO> (initial setting OFF (0))
OFF (0): User bits regenerated by the time code generator of this unit is
recorded.
ON (1): The user bit auto preset function is activated and the user bit
data stored in the built-in memory is recorded.
● Select the sub time code.
● Menu switch No. 450 <SUB TC (VITC) REC> (Initial setting: ON(1))
OFF (0): “00:00:00:00” is always recorded on the sub time code.
ON (1): Records the input VITC time code in the sub time code.
3. Record the time code.
Press the [PLAY] button while pressing the [REC] button.
[
The selected time code will be recorded.
Recording the time code data output from the external time code generator
Externally generated time code can be recorded after being regenerated with the
time code data output from the built-in time code generator.
POWER
ON I
OFF O
CH1 AUDIO
INPUT VIDEO
INPUT
AUDIO MONITOR
VIDEO CASSETTE RECORDER BR-D95U
CH2 CH3 CH4
CH1 CH2 CH3 CH4 CH1 CH2 CH3 CH4
SIF SDI AES/EBU
AUDIO INPUT / AUDIO MONITOR SELECT
LINE CPN L ANALOG R
SERVICE USE ONLY
TIME CDOE
INT DF FREE PRESET
EXT NDF REC REGEN
Variable Motion
COMPONENT DIGITAL
OFF RF HID GND 8 ON
ON 4 OFF
TIME CDOE INT FREE PRESET
EXT
DF
NDF REC REGEN
ON SCREEN CF (625)
101
10-4 TIME CODE PLAYBACK
10 HOW TO USE TIME CODE
Time code is output through the rear panel [TC OUT] and [VIDEO OUT] connectors during playback. VITC time
code with the time code data superimposed on the video signal is output through the [VIDEO OUT-LINE] connector.
Sub time code is output through the [VIDEO OUT-LINE] connector as VITC time code when menu switch No. 451
<VITC OUT SELECT> is set to “SUB TC”. Only the main time code is output through the [TC OUT] connector.
Setting
1. Front panel switch setting
● Select a Counter Display mode to TC or UB with the [COUNTER] and [SHIFT]
buttons.
2. Menu switch setting
● For VITC time code output, select a line to be added to the video signal.
● Menu switch No. 400 <VITC LINE-1 SELECT>
(Initial setting: NTSC 16 LINE/PAL 19 LINE)
● Menu switch No. 401 <VITC LINE-2 SELECT>
(Initial setting: NTSC 18 LINE/PAL 21 LINE )
● Select VITC time code output through the [VIDEO OUT] connector.
Menu switch No. 451 <VITC OUT SELECT>
SUB TC (0) : Outputs the VITC time code recorded in the sub time code.
TC (1) : Outputs the time code recorded in the main time code.
OFF : VITC time code is not output from the [VIDEO OUT]
connector.
Factory setting : TC (1)
● Select the Time Code Output mode during search.
Menu switch No. 452 <SEARCH LTC>
OFF (0) : Outputs time code through the [TC OUT] connector during search
at X1.
ON (1) : Outputs time code through the [TC OUT] connector during search
at all speeds. Continuous time code is not available.
3. Play back the time code.
Press the [PLAY] button.
[ The selected time code is played back.
TCR or UBR is shown with the on-screen time code data.
● LTC time code is output from the [TC OUT] connector.
● Main or sub time code selected with menu switch No. 451 <VITC OUT
SELECT> is superimposed on video signals and output to the line selected
with menu switch No. 400 and No. 401 from the [VIDEO OUT] connector.
● On-screen display of sub
time code
Sub time code is displayed
with the main time code
when menu switch No. 451
<VITC OUT SELECT>
is set to “SUB TC (0)”.
POWER
ON I
OFF O
M H F S
REC
MENU
PLAY PAUSE/STILL
REW STOP FF
EJECT
PHONES CH1 CH2 CH3 CH4 REC
PLAY
PULL FOR VARIABLE
TRACKING
CH1
CH1
CH2 CH3 CH4/ TRACKING
SET HOLD PB PB/EE
COUNTER UB CONDITION
AUDIO
INPUT VIDEO
INPUT
AUDIO MONITOR
PULL
RELEASE
RESET VCON REMOTE
TOP VIDEO AUDIO
OTHERS ON SCREEN TIME CODE SERVO/SYS USER
INSERT
STAND BY
PLAYER SEARCH VAR
P.PLAY
DA3 DA2 DA1 VIDEO ASSEM
IN ENTRY OUT
CANCEL
SHIFT REVIEW
METER MODE TRACKING FINE PREVIEW AUTO EDIT PREROLL
TC
RECORDER
DA4
VIDEO CASSETTE RECORDER BR-D95U
STILL
X-1
REV FWD
X1
CH2 CH3 CH4 CH1 CH2 CH3 CH4
CH1 CH2 CH3 CH4
SIF SDI AES/EBU
AUDIO INPUT / AUDIO MONITOR SELECT
LINE
CPN L ANALOG R
PULL RELEASE
CTL P.READ AUTO OFF V.VAR REMOTE PB/EE 16:9 TC UB DF SERVO GEN CF AP 525 OVER
–60 –2 –4
+2 +4
0
–40 –30 –20 –10 0 dB dB R P OVER
–60 –2 –4
+2 +4
0
–40 –30 –20 –10 0 dB dB R P OVER
–60 –2 –4
+2 +4
0
–40 –30 –20 –10 0 dB dB R P OVER
–60 –2 –4
+2 +4
0
–40 –30 –20 –10 0 dB dB R P 625
Variable Motion
COMPONENT DIGITAL
[PLAY] button
[COUNTER] button
● When you are using this
deck as a player, the
recording time code may
not be regenerated when
you output embedded
audio (SERIAL V/A OUT)
signals to the BR-D750U,
BR-D85U or BR-D80U. In
this case, set menu switch
No. 237 <EMBEDDED
AUDIO> to “OFF”.