Schneider Electric ALTIVAR 58 TRX - Manual (Page 83)

Altivar ® 58 TRX AC Drives
Communication Parameters
83
09/2003 © 2000–2003 Schneider Electric All Rights Reserved
W262
or 16#5FE5/D JOG 0.1 Hz Jog frequency 0 to 100 (0.0 to 10.0 Hz)
W263
or 16#5FE5/E JGT 0.1 s Delay between two consecutive jog operations 0 to 20 (0.0 to 2.0 s)
W264
or 16#5FE5/F SP2 0.1 Hz Preset speed 2 LSP to HSP
W265
or 16#5FE5/10 SP3 0.1 Hz Preset speed 3 LSP to HSP
W266
or 16#5FE5/11 SP4 0.1 Hz Preset speed 4 LSP to HSP
W267
or 16#5FE5/12 SP5 0.1 Hz Preset speed 5 LSP to HSP
W268
or 16#5FE5/13 SP6 0.1 Hz Preset speed 6 LSP to HSP
W269
or 16#5FE5/14 SP7 0.1 Hz Preset speed 7 LSP to HSP
W270
or
16#5FE5/15 IDC 0.1 A DC injection current level 0.1 to 1.36
x INV (drive controller nominal current)
W271
or 16#5FE5/16 TDC 0.1 s DC injection time (in the case of automatic DC
injection at stop)
Type FVC: Zero speed holding time with CTR =
closed loop 0 to 300 = 0.0 s to 30.0 s
301 = CONT: continuous injection
W272
or 16#5FE5/17 TLS 0.1 s Low speed (LSP) dwell timer 0 = No: no limit
1 to 9999 = time of 0.1 s to 999.9 s
W273 [1]
or 16#5FE5/18
BRL 0.1 Hz Mechanical brake release threshold 0 to 100 (0.0 to 10.0 Hz)
W274
or 16#5FE5/19 BEN 0.1 Hz Mechanical brake engage threshold
Type FVC: Not significant if
CTR = closed loop 0 to LSP
W275
or 16#5FE5/1A BRT 0.01 s Mechanical brake release time 0 to 500 (0.00 to 5.00 s)
W276
or 16#5FE5/1B BET 0.01 s Mechanical brake engage time 0 to 500 (0.00 to 5.00 s)
W277
or 16#5FE5/1C IBR 0.1 A Mechanical brake release current threshold 0 to 1.36
x INV (drive controller nominal current)
W278
or 16#5FE5/1D TL2 1% Second torque limit 0 to 200
W279
or 16#5FE5/1E RPG 0.01 PI proportional gain 1 to 10000 (0.01 to 100.00)
W280
or 16#5FE5/1F RIG 0.01/s PI integral gain 1 to 10000 (0.01 to 100.00)
W281 [1]
or 16#5FE5/20
FBS 0.1 PI feedback scale factor 10 to 1000 (1.0 to 100.0)
W282
or 16#5FE5/21 CTD 0.1 A Motor current threshold for signalling 0.25 to 1.36 x INV
(INV = drive controller nominal current)
W283
or 16#5FE5/22 TTD 1% Thermal threshold for signalling 0 to 118
W284
or 16#5FE5/23 FTD 0.1 Hz Frequency threshold for signalling LSP to HSP
W285
or 16#5FE5/24 DTS 0.01 Tachogenerator feedback scaling (For I/O card
with analog input) 100 to 200 (1.00 to 2.00)
W286
or 16#5FE5/25 JPF 0.1 Hz Skip frequency
(frequency range: ±2.5 Hz) 0 to HSP
W287
or 16#5FE5/26 PIC — Inverts the PI feedback signal 0 = No (normal)
1 = Yes (inverted)
W288
16#5FE5/27 SDC 0.1 A Continuous DC injection braking current level on
stopping after 30 s. See TDC (W271) Min: 0.1 x INV
Max: 1.36 x INV
(INV = drive controller nominal current)
W289
or 16#5FE5/28 USC 0.01 Machine coefficient. Applied to RFR for custom
display of machine speed under Display parameter
USP (USP = RFR x USC). 1 to 10000 (0.01 to 100.00)
W290
or 16#5FE5/29 BIP — Brake release pulse 0 = No: Pulse in the direction requested
1 = Yes: Always pulse in the ascending direction
W291
or 16#5FE5/2A INR — Fine increment in the ramp settings for ACC, DEC,
AC2, and DE2 0 = 0.1 s
1 = 0.01 s
W292
or 16#5FE5/2B SRP 1% Range of action around the reference for +/–
speed function 0 to 50% of the reference
W293
or 16#5FE5/2C TA1 1% Rounding of the start of the acceleration ramp 0 to 100% of ramp time
Adjustment Registers (Continued)
Word Code Units Description Possible Values or Range
[1] This parameter does not exist for ATV58 Type FVC drive controllers.