Schneider Electric ALTIVAR 58 TRX - Manual (Page 22)

Altivar ® 58 TRX AC Drives
Description of Type FVC Control Terminals
© 2000–2003 Schneider Electric All Rights Reserved
22
09/2003
DESCRIPTION OF ATV58 TYPE FVC CONTROL TERMINALS
The ATV58 Type FVC control terminals are shown below. The location of the control terminal strip varies
from model to model. See page 18.
The control terminal strip contains four pull-apart terminal blocks, one for the relay outputs and three for
the low-level inputs and outputs. The S terminals are used to connect shield wires of multi-conductor
control cables for the low level inputs, outputs, and encoder. Maximum wire size for all control terminals
is 16 AWG (1.5 mm
2
). Tightening torque is 2.2 lb-in (0.25 N•m). The characteristics of the control
terminals are shown in the table below.
Function of Terminals
Terminals Function Electrical Characteristics
R1A
R1B
R1C R1A to R1C is a N.O.
contact. When the drive
controller is powered with no
fault, the contact is closed.
R1B to R1C is a N.C.
contact. When the drive
controller is powered with no
fault, the contact is open.
• Minimum switching capacity: 10mA for 24 Vdc.
• Maximum switching capacity on inductive load: 1.5 A for 250 V Vac (cos
ϕ 0.4) and
30 Vdc (L/R 7 ms).
• Maximum response time: 20 ms.
R2A
R2C N.O. contact of R2
programmable relay
COM Common for logic and
analog inputs
AI1A
AI1B Differential analog input • ± 10V, impedance 40 k Ω in differential mode, 20 k Ω in common mode.
• Maximum permissible voltage ± 30 V.
• Resolution 11 bits + sign.
• Accuracy ± 0.5% of maximum value.
• Linearity ± 0.2% of maximum value.
• Sampling time 2 ms maximum.
+ 10 Supply for reference
potentiometer (1 to 10 k
Ω)
• Voltage + 10 V (-0 + 10%) 10 mA maximum protected against short circuits and
overloads.
AI2 Programmable analog input • Input 0-20 MA, programmable for X-Y mA by configuring X and Y (0 to 20).
• Impedance 100
Ω.
• Maximum permissible current 50 mA.
• Resolution 0.02 mA.
• Accuracy ± 1% of maximum value.
• Linearity ± 5% of maximum value.
• Sampling time 2 ms maximum.
AO1 Programmable analog
output • Output 0-20 MA, programmable for X-Y mA by configuring X and Y (0 to 20).
• Load impedance 500
Ω maximum.
• Resolution 0.02 mA.
• Accuracy ± 1% of maximum value.
• Linearity ± 5% of maximum value.
• Sampling time 2 ms maximum.
LI1
LI2
LI3
LI4 Programmable logic inputs
function depends on
configuration • Impedance 3.5 k Ω .
• Power supply + 24 V (maximum 30 V).
• State 0 if < 5 V, state 1 if > 11V.
• Sampling time 2 ms maximum.
+ 24 Power supply for logic inputs • Voltage + 24 V protected against short circuits and overload, minimum 18 V,
maximum 30 V.
• Maximum current 120 mA.
A
A-
B
B- Encoder inputs • For Incremental optical encoder with RS422-compatible differential outputs.
• Impedance 330
Ω .
• Maximum 5000 pulses/rev., minimum 100 pulses/rev.
• Maximum frequency 200 kHZ at high speed (HSP).
+ 5 V
0 V Power supply for encoder • Voltage 5 V (maximum 5.5 V) protected against short circuits and overloads.
• Maximum current 200 mA.
R1A R1B R1C R2A R2C COM AI 1A AI1B + 10 AI 2 A01 A A- B B- 5 V 0 V LI 1 LI 2 LI 3 LI 4 + 24
Shielding connection screw for
analog I/O and logic inputs
Shielding connection
screw for encoder
cable
S S
ar
ra
ng
e o
f t
e
rm
s cop
y.
e ps