Sanyo DWM-3500 - Manual (Page 23)

-E22-
Adjusting the Speaker Volume Balance
This unit is set to the standard level before shipping from the
factory. You may not need adjustment.
But, depending on the size of the room and the placement of the
speakers, you may need a fine adjustment.
In this case, follow the steps below. Please use the remote
control at the listening point.
4 , 5
2, 5, 9
1, 11
ENTER
3, 4, 6
8
1. Press [SETUP/MENU].
When the unit is in DVD mode and in the Stop mode or disc is
not inserted, press [SETUP/MENU] twice.
The “MENU” screen appears on the TV screen.
MENU
TIMER REC SET
AUTO REPEAT ON OFF
ON OFF SAP
CH SETUP
SYSTEM SETUP
2. Press [ 4 ] or [ 5 ] to select “SPEAKER SETUP”.
MENU
TIMER REC SET
AUTO REPEAT ON OFF
ON OFF SAP
CH SETUP
SYSTEM SETUP
SPEAKER SETUP
TVGuardian SETUP
3. Press [ENTER].
The “SPEAKER SETUP” screen appears on the TV screen.
SPEAKER SETUP
VOL. ADJUST
DELAY ADJUST
4. Press [ENTER].
The “VOL. ADJUST” screen appears on the TV screen.
VOL. ADJUST
F–L
SUBWOOFER
TRIM
TEST TONE
CENTER F–R
SURR.L VOL. – 0 SURR.R
5. Press [ 4 ] or [ 5 ] to select “TEST TONE”.
6. Press [ENTER].
7. The test tone will be heard from each speaker for 2 seconds
in the following order.
TV screen Speaker
F-L Front left Speaker
CENTER Center Speaker
F-R Front right Speaker
SURR.R Surround right Speaker
SURR.L Surround left Speaker
8. Press [VOLUME] + or – until the test tone is at a comfortable
level.
9. If the test tone level is not the same from each speaker, press
[ 4 ] or [ 5 ] to adjust it while the speaker is activating.
F-L/F-R: “0” ~ “–10”
CENTER/SURR.R/SURR.L: “+10” ~ “–10”
10. Repeat steps 8 ~ 9 for other settings.
11. Press [SETUP/MENU] until the menu screen is cleared.
Adjusting the Speaker and Subwoofer Level
1, 10
ENTER
3, 4, 6, 7 4 , 5
2, 5, 8
1. Press [SETUP/MENU].
When the unit is in DVD mode and in the stop mode or disc is
not inserted, press [SETUP/MENU] twice.
The “MENU” screen appears on the TV screen.
MENU
TIMER REC SET
AUTO REPEAT ON OFF
ON OFF SAP
CH SETUP
SYSTEM SETUP
SPEAKER SETUP
TVGuardian SETUP
2. Press [ 4 ] or [ 5 ] to select “SPEAKER SETUP”.
MENU
TIMER REC SET
AUTO REPEAT ON OFF
ON OFF SAP
CH SETUP
SYSTEM SETUP
SPEAKER SETUP
TVGuardian SETUP
3. Press [ENTER].
The “SPEAKER SETUP” screen appears on the TV screen.
SPEAKER SETUP
VOL. ADJUST
DELAY ADJUST
4. Press [ENTER].
The “VOL. ADJUST” screen appears on the TV screen.
5. Press [ 4 ] or [ 5 ] to select “TRIM”.
VOL. ADJUST
F–L
SUBWOOFER
TRIM
TEST TONE
CENTER F–R
SURR.L VOL. – 0 SURR.R
6. Press [ENTER].
VOL. ADJUST
F–L
SUBWOOFER
TRIM
TEST TONE
CENTER F–R
SURR.L VOL. – 0 SURR.R
7. Press [ENTER] repeatedly to select the desired speaker.
Each time the button is pressed, the selected speaker and
tone level flash.
8. Press [ 4 ] or [ 5 ] to adjust the level as desired.
F-L/F-R: “0” ~ “–10”
CENTER/SURR.R/SURR.L/SUBWOOFER: “+10” ~ “–10”
Note: No test tone.
9. Repeat steps 7 ~ 8 for other settings.
10. Press [SETUP/MENU] until the menu screen is cleared.
Note:
If no adjustment are made, the original display returns after
approximately 60 seconds.
2B80201A [E] P17-26 24/2/03, 7:13 PM 22