Sanyo DWM-3500 - Manual (Page 35)

-E34-
Timer Recording
Timer recording can be programmed on-screen with the remote
control. The built-in timer allows automatic unattended recording
of up to 8 programs within 1 month.
Preparation:
•
Set the clock correctly (see pages E17 ~ E19).
• Press [VCR] to select the VCR mode. (The VCR indicator on
the front panel will light.)
• Load a cassette tape with the erase prevention tab intact.
• Press the [DISPLAY] button to verify that the time and date
are correct (see page E32).
Example: Program a timer recording for the 26th day, channel
125 (CATV), 11:00 – 11:30 PM on timer program number 1
(Tape speed: SLP).
1. Press [SETUP/MENU].
The “MENU” screen appears on the TV screen.
MENU
TIMER REC SET
AUTO REPEAT ON OFF
ON OFF SAP
CH SETUP
SYSTEM SETUP
SPEAKER SETUP
TVGuardian SETUP
2. Select “TIMER REC SET”, then press [ENTER].
MENU
TIMER REC SET
AUTO REPEAT ON OFF
ON OFF SAP
CH SETUP
SYSTEM SETUP
SPEAKER SETUP
TVGuardian SETUP
3. Press [ 4 ] or [ 5 ] to select one of the program line, then press
[ENTER].
DATE START END CH
–
4. Press [ 4 ] or [ 5 ] to select the date, then press [ENTER].
DATE START END CH
26 WE
5. Set the start time, end time, channel and tape speed as in
step 4.
DATE START END CH
11:00 PM 11:30 PM 125 SLP 26 WE
Notes:
•
Press [CLEAR/CANCEL] to move cursor backward for
correction.
• To record from external source, set the channel to “L”. “L” will
appear next to CH 125 (or 69).
6. Repeat steps 3 ~ 5 for other programs.
• To return to the normal screen, press [SETUP/MENU]
twice.
DATE START END CH
26 WE 11:00 PM 11:30 PM 125 SLP
7. Press [TIMER REC].
The clock symbol ( ) will appear on the FL display and the
VCR stands by for recording. At the same time, VCR mode
will change to DVD mode automatically. You can use DVD
even if the VCR is in the Timer recording mode.
If you do not use the DVD, turn the power off.
The timer recording will start at 5 seconds before the time you
predetermined.
Notes:
•
If the clock symbol ( ) does not appear on the FL display in
spite of the pressing of [TIMER REC], the cassette may not
have been loaded yet (see page E27).
• If the cassette is ejected in spite of the pressing of [TIMER
REC], the erase prevention tab of the cassette may have
been removed (see page E27).
• If the clock symbol ( ) blinks on the FL display when the
timer recording ended, the TV program has not been
completely recorded because of an insufficient tape supply.
Press [TIMER REC] to cancel the timer program or press [
q
EJECT] to remove the cassette tape.
• During timer recording standby mode, the VCR mode cannot
be selected. To use the VCR, press [TIMER REC] at first,
then press [VCR] to change to VCR mode. After you use the
VCR, press [TIMER REC] again to put the VCR into timer
recording standby mode.
• If you press [TIMER REC] during timer recording, the recording
operation will be interrupted. If you press [TIMER REC] again
within the programmed time, the recording operation will start
again.
• After a power failure or disconnection of the power plug, all
programmed recording settings and time display will be lost
upon resumption of power. In this case, reset the clock (see
page E19) and reprogram any timer recordings.
TIMER REC
ENTER
DISPLAY
VCR
4 , 5
CLEAR/
CANCEL
SETUP/
MENU
2B80201A [E] P27-37 24/2/03, 7:14 PM 34