Precaution regarding use, Copyright, Handling the discs – Pioneer DVD-V7300D User Manual

Page 8: Lens cleaning, Condensation, Installation, Operating environment, Moving the player, 7handling, 7stacking

Advertising
background image

8

En

Copyright

÷

Unauthorized public preference, broadcasting, or copying is
a violation of applicable laws.

÷

This product incorporates copyright protection technology
that is protected by method claims of certain U.S. patents
and other intellectual property rights owned by Macrovision
Corporation and other rights owners. Use of this copyright
protection technology must be authorized by Macrovision
Corporation, and is intended for home and other limited view-
ing uses only unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly is prohib-
ited.

Handling the discs

7

Handling

÷

Never play clacked, scratchesd or warped disc. This may damage
the player or cause it to malfunction.

÷

Do not damage or dirty the signal surface of the disc.

÷

Do not affix paper and seals to the disc.

÷

Too much glue will cause a malfunction. Many rental discs, particu-
larly, have labels affixed to them, and use the disc after confirming
that there is no glue.

7

Stacking

÷

Store the discs carefully. If you store discs at an angle, or stacked on
top of each other, discs may become warped even when in their
jackets.

÷

Read the operating instructions included in discs.

7

Cleaning

÷

Fingerprints or other dirt on the disc may affect sound and pic-
ture quality. To remove dirt or finger prints, wipe gently from the
inside toward the outer edges. (Do not wipe in a circular direc-
tion.)

÷

Discs must not be cleaned with record cleaning sprays, or static pre-
vention sprays, etc. Also do not use volatile liquids such as benzine,
or thinner, etc.

÷

To clean your discs, use a soft clean cloth to wipe them. If necessary,
moisten a soft cloth with diluted neutral detergent to remove heavy
dirt or fingerprints.

7

Discs with special shapes

Discs with special shapes (heart shaped discs, hexagonal discs, etc.)
cannot be played on this set.
Attempting to do so may damage the set. Do not use such discs.

Lens cleaning

The player’s pickup lens should not become dirty in normal use but if
for some reason it should malfunction due to soiling, contact your near-
est PIONEER authorized service centre. Lens cleaners are commer-
cially available but special care should be exercised in their use since
some may cause damage to the lens.

Condensation

Moisture will form in the operating section of the player if the player is
brought from cool surroundings into a warm room or if the temperature
of the room rises suddenly. When this happens, player’s performance
will be impaired.
To prevent this, let the player stand in its new surroundings for about
an hour before switching it on, or make sure that the room temperature
rises gradually.
Condensation may also form during the summer if the player is ex-
posed to the breeze from an air conditioner. In such cases, change the
location of the player.

Installation

÷

Install the player in a level and stable location.
Do not use in shaky, unstable locations, or locations exposed to much
vibration.

÷

Do not impair the player’s cooling functions. Avoid placing on long-
pile carpets, etc.. Also do not wrap or cover with towels or cloths
when in use. Such coverings can impede the player’s cooling func-
tion and result in internal damage.

÷

Do not place objects on top of the player.

÷

Install in a location which is not exposed to heat sources. Avoid in-
stalling the player above an amplifier or other heat-emitting compo-
nent. If installing the player in a component rack, select a rack with
good ventilation, located well below the amplifier.

÷

If the player is installed in a rack, care must be taken to avoid internal
temperature buildup. Position it so that the ventilation openings in
the top and bottom of the player are not obstructed.
As a rule, install so that there is no heat from below and leave a gap
of 10 cm or more at the left and right and above so that air can flow
around the device by natural convection at a room temperature of
35

°

C or less. If installation is necessary in any other circumstances,

ensure that the air temperature at a point 5 cm above the center of
the player in a sufficiently warmed up state is no higher than 35

°

C.

When necessary, use forced air cooling.

÷

When multiple players are connected in parallel, a high surge cur-
rent will be impressed on the units when external power is first turned
on. Please consult your Pioneer dealer regarding ratings for the power
switch to be used.

÷

Do not install the player in a closed rack. An internal temperature
builts up and results in internal damage.

Operating Environment

Operating environment temperature and humidity:
+5°C - +35°C ; less than 85% RH (cooling vents not blocked)

7

Do Not Install in the Following Locations:

÷

Locations exposed to direct sunlight or strong artificial light

÷

Locations exposed to dust or smoke

÷

Locations subject to vibration

÷

Locations subject to strong electro-magnetic fields.

÷

Near sources of heat.

÷

Locations exposed to high levels of electronic noise

÷

Locations subject to electrostatic noise

÷

Locations exposed to high humidity, or poorly ventilated locations

÷

A closed rack

Moving the Player

When transporting this player to a new location, be sure to use the
packaging provided and avoid subjecting the player to vibration, shock,
or dropping. During transport, protect the player from exposure to heat
or water.
Before packaging the player, remove any disc loaded, since moving
the player with a loaded discs may cause damage to the disc or play-
er’s internal parts.

Precaution regarding use

Special Precautions!

Never attempt to move the player while a disc is playing.
Discs rotate at very high speeds during play, and lifting or
moving the player at such times could cause damage to the
disc. Also, subjecting the player to strong impact or vibration
when a disc is loaded may cause damage to disc or player.
Be sure the player is stopped and no disc is loaded before
moving the player. Also be sure that no disc is loaded when
lifting the player.
This component is built using precision optical parts. Be
sure to take care to control temperature and dust inside
the room where this player is installed.

Advertising