Pioneer PDP-501MX - Manual (Page 105)

105
Command
Name
Full Name
Normal
Validity
Direct
Validity
Function
Up/
Down
Validity
RS-232C Adjustment Mode
ABN
ABY
AJN
AJY
APN
APY
AZN
AZY
BBY
BRT
BHI
BLW
BSL
BR1
BR2
BR3
BR4
BR5
CFR
CL1
CL2
CM1
CM2
CNT
COL
CP1
CP2
CPH
DTL
DIN
DIY
DOF
DW0
DWn
DWF
FRP
FRW
ABL NO
ABL YES
ADJUST NO
ADJUST YES
AUTO POWER OFF NO
AUTO POWER OFF YES
FULL AUTO ZOOM NO
FULL AUTO ZOOM YES
VIDEO RGB YES
BRIGHTNESS
BLUE HIGH
BLUE LOW
BLUE SIDE MASK LEVEL
BAUD RATE 1
BAUD RATE 2
BAUD RATE 3
BAUD RATE 4
BAUD RATE 5
CLOCK FREQUENCY
CLAMP MODE 1
CLAMP MODE 2
COLOUR MODE 1
COLOUR MODE 2
CONTRAST
COLOUR
VIDEO COMPONENT-1 YES
VIDEO COMPONENT-2 YES
CLOCK PHASE
DETAIL
OSD DISPLAY NO
OSD DISPLAY YES
DISPLAY OFF
DOWN 10
DOWN n
DOWN FULL
FRESH POSITION
FRESH WHITE BALANCE
X
X
X
?
X
X
?
?
X
X
X
X
X
X
X
X
X
X
X
X
X
?
?
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
?
?
?
?
X
X
X
X
X
?
X
X
X
X
?
?
X
X
?
?
X
X
X
—
—
—
X
X
X
X
X
X
X
X
X
X
X
?
?
?
?
X
X
X
X
X
?
X
X
X
X
?
?
X
X
?
?
X
X
X
—
—
—
X
X
A
B
C
D
F
5.5.3 List of RS-23C commands
Keys to the table
• Normal Validity: Shows availability in the normal operating mode. Commands shown as valid are so whether or
not preceded by an <AJY> command.
• Direct Validly: Shows commands that, if transmitted followed by numerical values, can or cannot directly set the
corresponding items to those values sent out.
• Up/Down Validity: Shows commands that, if transmitted followed by UPn/DWn (n standing for any numbers from 0
to 9), can or cannot increase or decrease the corresponding current adjustments by those num-
bers.
O: Yes X: No
Sets ABL to OFF.
Sets ABL to ON.
Terminates RS-232C adjustment mode.
Initiates RS-232C adjustment mode.
Sets Auto Power Off to OFF.
Sets Auto Power Off to ON.
Sets Full Auto Zoom to OFF.
Sets Full Auto Zoom to ON.
Sets INPUT to VIDEO: RGB.
Adjusts BRIGHTNESS.
Adjusts BLUE HIGH-LIGHT.
Adjusts BLUE LOW-LIGHT.
Adjusts BLUE SIDE MASK LEVEL.
Sets RS-232C baud rate to 1200 bps.
Sets RS-232C baud rate to 2400 bps.
Sets RS-232C baud rate to 4800 bps.
Sets RS-232C baud rate to 9600 bps.
Sets RS-232C baud rate to 19200 bps.
Adjusts PLL frequency.
Sets Clamp Position Setting Mode to 1.
Sets Clamp Position Setting Mode to 2.
Sets White Balance Adjustment Data to Mode 1.
Sets White Balance Adjustment Data to Mode 2 (retake).
Adjusts CONTRAST.
Adjusts COLOUR (except when RGB is selected).
Sets INPUT to VIDEO: COMPONENT 1.
Sets INPUT to VIDEO: COMPONENT 2.
Adjusts PLL phase.
Adjusts DETAIL.
Disables OSD displays (excepting Menu screen and
some warnings).
Enables OSD displays (excepting Menu screen and
some warnings).
Turns OSD display OFF.
Decreases adjustment values by 10.
Decreases adjustment values by n.
Decreases adjustment values to minimum.
Sets phase adjustment data to median value.
Sets picture quality and white balance adjustment
data to median values.